Filter
Top Products
JBL and Harman International are trademarks of Harman
International Industries, Incorporated, registered in the United
States and/or other countries.
Studio Series, Pro Sound Comes Home, EOS, PolyPlas, HeatScape,
Symmetrical Field Geometry (SFG), IsoPower, FreeFlow and
Straight-Line Signal Path (SSP) are trademarks of Harman
International Industries, Incorporated.
Dolby is a registered trademark of Dolby Laboratories.
DTS is a registered trademark of DTS, Inc.
Mylar and Kapton are registered
trademarks of E.I. du Pont de
Nemours and Company
.
©2005 Harman International Industries, Incorporated. All rights reserved.
Part No.
353334-001
PRO SOUND COMES HOME
™
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
2, route de Tours, 72500 Chateau du Loir, France
www.jbl.com 516.255.4JBL (USA only)
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau du Loir
France
declare in own responsibility that the products described in this owner’s manual
are in compliance with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group International
Chateau du Loir, France 8/05
TROUBLESHOOTING
If there is no sound from
any of the speakers:
• Check that receiver/ampli-
fier is on and that a source is
playing.
• Review proper operation of
your receiver/amplifier.
If there is no sound
coming from one
speaker:
• Check the “Balance”
control on your receiver/
amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers.
• Make sure no wires are
touching other wires or
terminals and creating a
short circuit.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• In Dolby
®
Digital or DTS
®
modes, make sure that the
receiver/processor is config-
ured so that the speaker in
question is enabled.
• Turn off all electronics and
switch the speaker in ques-
tion with one of the other
speakers that is working cor-
rectly. Turn everything back
on, and determine whether
the problem has followed the
speakers, or has remained
in the same channel. If the
problem is in the same chan-
nel, the source of the prob-
lem is most likely with your
receiver or amplifier, and
you
should consult the owner’s
manual for that product for
further information.
If the
problem has followed the
speaker, consult your dealer
for further assistance or, if
that is not possible, visit
www.jbl.com for further
information.
If the system plays at
low volumes but shuts
off as volume is
increased:
• Check all wires and con-
nections between receiver/
amplifier and speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
If there is no (or low)
bass output:
• Make sure the polarities
(+ and –) of the left and right
“Speaker Inputs” are
connected properly.
• Consider adding a powered
subwoofer to your system for
use with digital “.1” surround
formats.
If there is no sound from
the surround speakers:
• Check all wires and con-
nections between receiver/
amplifier and speakers.
Make sure all wires are con-
nected. Make sure none of
the speaker wires are frayed,
cut, punctured or touching
each other.
• Review proper operation of
your receiver/amplifier and
its surround sound features.
• Make sure the movie or TV
show you are watching is
recorded in a surround
sound mode. If it is not,
check to see whether your
receiver/amplifier has other
surround modes you may
use.
• In Dolby Digital or DTS
modes, make sure your
receiver/processor is config-
ured so that the surround
speakers are enabled.
• Review the operation of your
DVD player and the jacket of
your DVD to make sure that
the DVD features the desired
Dolby Digital or DTS mode,
and that you have properly
selected that mode using both
the DVD player’s menu and the
DVD’s menu.