Filter
Top Products
9
NS-SBAR/NS-SBAR-A Soundbar Home Theater System
www.insigniaproducts.com
To turn off the second room signal:
1 On the soundbar, press both the Wireless Next
Source button and the Volume Down button
for five or more seconds.
2 The Audyssey Dynamic Volume Red indicator
LED will briefly flash on/off twice, to show that
the second room signal is now off.
To turn on the second room signal:
1 On the soundbar, press both the Wireless Next
Source button and the Volume Down button
for five or more seconds.
2 The Audyssey Dynamic Volume Red indicator
LED will briefly turn on to show that the second
room signal is now on.
Care and maintenance
Use the following guidelines to maintain the
appearance of your soundbar:
• Use a soft, dry cloth to clean the soundbar.
• Avoid using harsh detergents or cleaning fluids.
• Do not vacuum any of the soundbar components,
because permanent damage could result.
Troubleshooting
Check the following information for the possible
cause and solution for a problem before contacting
the nearest service center or dealer for repairs.
Specifications
Legal notices
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of
this product is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply within the
limits for a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Symptom Solution
The soundbar does not
turn on
• Securely connect the power supply cable from the
AC power supply to the soundbar and the AC
power cable from the AC power supply to an AC
power outlet.
No sound
• Make sure that all connections are correct.
• Press the Volume + button.
• Press the INPUT button to choose the right sound
source.
• If you are using Rocketboost input, press the Next
Source button to select another sound source.
No communication
between the soundbar
and your Rocketboost
device
• Make sure that the Hub Status switch on the
sender/receiver is set correctly.
• Make sure that the power indicators on the
sender/receiver and the soundbar turn solid
blue/green. If the power indicators blink slowly, it
means there is no active link between the devices.
Unplug the AC power cables, then plug them back
in and try to establish the link again. (See “To
establish communications with other Rocketboost
devices:” on page 7.)
The remote control
doesn't work
• Replace the batteries
• Operate the remote more closely to the soundbar.
The sound from the left
and right channels is
reversed
• Check the left and right channel connections and
connect them correctly.
Length 38 in (965 mm)
Depth 4.6 in (117 mm) without wall mount bracket
5.5 in (139.7 mm) with wall mount bracket
Height 3.4 in (86 mm) without mounting feet
4.3 in (109.2 mm) with mounting feet
Total power 120 W (< 3% THD+N)
Power per channel 30 W for L and R channels
60 W for subwoofer
Speakers 2 x 0.75” tweeters
2 x 2.0” midranges
2 x 3.5” woofers
NS-SBAR_11-0299_MAN_V4.book Page 9 Thursday, March 31, 2011 7:49 AM