Filter
Top Products
6
O
PERATION
Surround Modes
When using the TSS-450 in a Dolby* Digital or DTS home theater
system, make sure all speakers are set to “Small”.When using the
system in a Dolby Pro Logic* home theater system,make sure the
receiver’s center channel mode is set to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode, e.g., CD-stereo,
videotape, Dolby Digital, Pro Logic.In each case, follow your
equipment’s instructions to ensure that the subwoofer output is
turned on and that the speakers are set to “Small”in each mode.
If your receiver has adjustable crossover settings, we recommend
the subwoofer crossover be set between 100Hz –120Hz.
Power On
Plug your subwoofer’sAC cord into a wall outlet.Do not use the
outlets on the back of the receiver.
Initially set the Subwoofer Level Control
ᕥ
to the“MIN”position.
Turn on the subwoofer by pressing the Power Switch
ᕦ
on the
rear panel.
Turn on your entire audio system and start a CD or movie
soundtrack at a moderate level.
Auto On/Stand-By
With the Power Switch
ᕦ
in the AUTO position, the LED on
the rear panel will remain lit in red or green to indicate the
On/Stand-By mode of the subwoofer.
RED = STAND-BY (No signal detected,Amp Off)
GREEN = ON (Signal detected,Amp On)
The subwoofer will automatically enter the Stand-By mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a signal
is detected. During periods of normal use, the Power Switch
ᕦ
can be left on.You may turn off the Power Switch
ᕦ
for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer Level Control
ᕥ
up about half way.If no
sound emanates from the subwoofer, check the AC-line cord and
input cables.Are the connectors on the cables making proper
contact? Is the AC plug connected to a “live”receptacle? Has the
Power Switch
ᕦ
been pressed to the “On”position? Once you
have confirmed that the subwoofer is active, proceed by playing a
CD or DVD. Use a selection that has ample bass information.
Set the overall volume control of the receiver/processor to a
comfortable level.Adjust the Subwoofer Level Control
ᕥ
until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots of
bass.This is not entirely true.A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural.An experienced
listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
TSS-450
Final Positioning
After correctly connecting the TSS-450 system and verifying that
both the subwoofer and all satellite speakers are playing, it is
time to optimize the system for your particular listening room.
Earlier, you placed the subwoofer in its general location. Finding
the exact location for optimum performance sometimes only
involves moving the speakers up to a few inches in any
direction.We urge you, therefore, to experiment with placement,
if possible, until your speakers deliver their full potential.
M
AINTENANCE AND
S
ERVICE
The satellite and subwoofer enclosures may be cleaned using a
soft cloth to remove fingerprints or to wipe off dust.
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections, atmospheric conditions,
and other factors, but once per year is the minimum.
If a problem occurs,make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse
the connection wires to the left and right system. If the problem
remains in the same speaker, then the fault is with the loud-
speaker. If the problem appears in the opposite speaker, the
cause is in another component or cable. In the event that your
TSS-450 ever needs service, contact your local Infinity
dealer or Infinity directly at 516-674-4INF (USA only) or
www.infinitysystems.com for a service center near you.
INFP1408TSS-450 OM 8/11/03 4:38 PM Page 9