Filter
Top Products
SPECIFICATIONS
653.1cs
Type: 6-1/2" 3-Way System
Speaker Impedance: 4 ohms
Power Handling: 120 watts per channel
Frequency
Response (±3dB): 50Hz ~ 45kHz
Sensitivity: 89Hz @ 2.83 V, 1 watt
Crossover Frequencies: Woofer
Hi terminal: 210Hz
Lo terminal: 130Hz
Midrange: 400Hz
Tweeter: 12.5kHz
Mounting Depth,
Drop-in Woofer: 2-1/2"(67.5 mm)
Cut-out
Diameter Woofer: 5-11/16" (149 mm)
Mounting Depth,
Drop-in Midrange: 1-13/16" (46 mm)
Cut-out
Diameter Midrange: 3-3/4" (96 mm)
Mounting
Depth Tweeter: 1" (25.4 mm)
Cut-out
Diameter Tweeter: 3-3/8" x 1-3/4"
(84.6 mm x 44.7 mm)
1.1cs
Type: 6" x 9" 3-Way System
Speaker Impedance: 4 ohms
Power Handling: 200 watts per channel
Frequency
Response (±3dB): 36Hz ~ 45kHz
Sensitivity: 89Hz @ 2.83 V, 1 watt
Crossover Frequencies: Woofer
Hi terminal: 210Hz
Lo terminal: 130Hz
Midrange: 400Hz
Tweeter:12.5kHz
Mounting Depth
Drop-in Woofer: 2-9/16" (65 mm)
Cut-out
Diameter Woofer: 5-11/16" x 8-3/4"
(149 mm x 223 mm)
Mounting Depth,
Drop-in Midrange: 1-13/16" (46 mm)
Cut-out
Diameter Midrange: 3-3/4" (96 mm)
Mounting
Depth Tweeter: 1" (25.4 mm)
Cut-out
Diameter Tweeter: 3-3/8" x 1-3/4"
(84.6 mm x 44.7 mm)
DECLARATION OF CONFORMITY
We, Infinity Systems A/S
Kongevejen 194B
DK-3460 Birkerød
DENMARK
Steen Michaelsen
Infinity Systems A/S
Birkerød. DENMARK. 2/98
declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards:
EN 50 081-1/1992
EN 50 082-1/3.1995
®
Infinity Systems, Inc. • 250 Crossways Park Drive,
Woodbury, NY 11797 USA • (516) 496-3400 • FAX (516) 682-3583
A NOTE ON POWER HANDLING
The speakers used in Kappa Series 3-Way
Component Systems are designed to produce rea-
sonable volume levels with little amplifier power.
However, the addition of an amplifier to drive
your speakers and a subwoofer will enhance the
dynamic range of your system, and help over-
come the ambient noise in a moving vehicle.
Kappa speakers are designed to handle the power
of a dedicated amplifier driven at or below its
rated power. If an amplifier is driven far above its
rated power, the output signal will “clip,” and the
additional power present in a clipped signal can
damage any speaker. Distorted or “fuzzy” sound
from your speakers is an indication that the ampli-
fier has exceeded its rated power, and you should
reduce the volume level
GENERAL CARE
The loudspeaker grilles may be cleaned with a
slightly damp cloth. Do not use any cleaners or
solvents on the grilles or the speaker cones.
ADJUSTING THE SOUND
After you have connected all the speakers to the
crossover according to the connection diagram,
you may adjust the overall sound of the system to
suit your taste.
The output of the woofers may be decreased by
moving the woofer + connection at the crossover
to the low position.
The output of the midrange may be decreased by
moving the midrange + connection at the
crossover to the low position.
The output of the tweeter may be increased by
moving the tweeter + connection at the crossover
to the high position or decreased by moving it to
the low position.
Kappa 653.1cs OM 7/14/98 10:10 AM Page 4