Filter
Top Products
Getting Started
Before using your i.Cube (“headset”) for the first time, please ensure that
1. the headset is fully charged;
2. the fully charged headset must be paired and connected with a Bluetooth mobile
phone.
Charging Your Headset
The headset comes with a built-in rechargeable battery. Prior to using the headset for
the first time, you are recommended to fully charge the battery.
5
Use only the supplied charger to charge the headset.
Charging Socket
fig.2
Status Status Indicator Audio
• Charging • Red light
• Fully charged • Blue light
• Low battery • Flashing red light • a short beep every 1 minute
• Out of battery • The light goes off
♦ 3 hours are required to fully charge the headset.
♦ Charging indication will be delayed for a few seconds if the headset has not been used
for a long time or the battery is drained.
6
Charging Your Headset (cont’d)
Pairing Your Headset with a Bluetooth Mobile Phone
1) Ensure the headset is off.
2) To activate the pairing mode, press and hold the headset’s MFB for 8 seconds without
releasing your finger until its status indicator flashes alternating blue and red lights.
3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “i.Cube” and
enter the passcode “0000”. When the pairing is completed, the headset’s status indicator
will flash a blue light rapidly five times.
If the pairing cannot be completed within three minutes after the pairing mode has been
activated, the headset’s status indicator will flash purple rapidly five times and then turns
off. Repeat steps 1 to 3 to pair both devices again.
Pairing Your Headset with Two Mobile Phones (Multipoint)
i.Cube supports a Multipoint function to allow simultaneous pairing of the headset
with two mobile phones.
1. Follow the pairing procedure as instructed in “Pairing Your Headset with a
Bluetooth Mobile Phone” to pair the headset with the first mobile phone.
2. Repeat the pairing procedure for the second mobile phone.
3. On the first mobile phone’s menu, activate its Bluetooth connection with the
headset.
7
8
When you turn on your headset for the first time, the headset automatically enters
the pairing mode, i.e. the status indicator flashes alternating blue and red lights.
This allows you to immediately pair your headset and mobile phone.
If your headset is paired with your mobile phone, press the MFB once more after
you turned on the headset to re-connect the mobile phone and the headset.
Using Your Headset
Using Your Headset (cont'd)
Function Button Audio Status Indicator
Power ON Press and hold the MFB for 2 a short beep Flashing blue light
seconds
Power OFF Press and hold the MFB for 2 a long beep
seconds
Say the voice tag as soon as you hear the short beep and you must have recorded the voice
tag into your mobile phone.
Function Button Audio Status Indicator
Answer a Call
Press the MFB once Flashing blue light
Answer a Second Call Press the MFB once to terminate a beep Flashing purple light
intended for your other
the first call, then press the MFB when there is a second
mobile phone once again to answer the second call intended for your
call other mobile phone
End a Call Press the MFB once Flashing blue light
Last No. Redial Double click the MFB Flashing blue light
Adjust Volume
Press the Vol＋/－once to a short beep
Flashing blue light
increase / decrease by 1 level
Mute a Call Press either volume key for 2
2 beeps every
Flashing blue light
seconds 5 seconds
Cancel Call Muting Press either volume key for 2 2 short beeps
Flashing blue light
seconds
Voice Dialing Press the MFB once
a short beep
Flashing blue light
Red light for two seconds
and then the light goes off
If you do not plan to use the headset for a while, you are recommended to turn off
the Bluetooth function of your mobile phone.