Filter
Top Products
14. Volume– Button
15. Volume+ Button
- 4 -
CONNECTING THE UNIT TO POWER
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet. Before switching on the unit, make sure that the voltage of your electricity supply is the same as that indicated
on the rating plate.
CONNECTING THE LOUDSPEAKERS
Connect the cables of the two loudspeakers to the corresponding input (R) for the right speaker and input (L) for the left speaker, located at the side of the unit.
Warning: Connect the loudspeakers before powering the unit. The unit may not work properly or get damaged if you use speakers different than the ones supplied with the unit.
SETTING THE TIME
Before starting to set the time, make sure that the unit is in POWER OFF Mode.
If you have iPod (Except iPod Shuffle) or iPhone
1.
Dock in the iPod/iPhone on the 30 pins Connector
2.
Press the ‘PLAY/PAUSE/SYNC’ button for a few seconds until the display will show SYNC with flashing, then the unit will synchronize the time same as the iPod/iPhone’s automatically.
If you do not have any iPod/iPhone units
1.
Press and hold the ‘FUNC/CL ADJ’ button for a few seconds, the hour digit in the display will start flashing.
2.
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to adjust the hour.
3.
When the correct hour is selected, press the ‘FUNC/CL.ADJ’ button again, the minute digit in the display will start flashing.
4.
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to adjust the minute.
5.
When the correct time is selected, press the ‘FUNC/CL ADJ’ button to store the time in the memory.
SETTING THE ALARM TIME
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode.
1.
Press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button on the unit once (you can also use the ‘AL1’ or ‘AL2’ button on the remote control) and the AL1 or AL2 icon will appear in the display.
2.
Press and hold the the ‘MEM-/AL1’ or ‘MEM+/AL2’ button then press the ‘FUNC/CL. ADJ.’ button to select the alarm wake up source. The options are buzzer, iPod/iPhone, Radio or CD.
3.
After setting the wake up source, the alarm hour digit will begin flashing.
4.
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit to adjust the alarm hour.
5.
When the desired alarm hour is selected, press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button again, (you can also use the ‘AL1’ or ‘AL2’ button on the remote control), the alarm minute digit will begin flashing.
6.
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit to adjust the alarm minute.
7.
When the desired alarm time is selected, press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button again to confirm. (You can also use the ‘AL1’ or ‘AL2’ button on the remote control).
Note : If you choose iPod/iPhone or CD as the alarm wake up source, please make sure that you have the iPod/iPhone or CD in place.
- 5 -
TURN OFF THE ALARM
When the alarm activates, press the ‘POWER/AL.OFF’ button to turn off the alarm.
SNOOZE FUNCTION
1.
Whenever the alarm activates, it can be temporarily suspended for a short period of 10 minutes by pressing the ‘SNOOZE’ button on the unit or the ‘SLEEP/SNOOZE’ button on the remote control.
2.
The alarm will then automatically activate again after the 10 minutes SNOOZE period has ended.
3.
This procedure can be repeated for up to approximately one hour.
RADIO OPERATION
1.
Press the ‘POWER/AL OFF’ button to turn on the unit.
2.
Press the ‘FUNC./CL.ADJ’ button to select the FM RADIO mode.
3.
Press and hold the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit for approx. 1 second, it will start to search the next radio station in the direction of the search. The search operation simply finds stations
with strong signals. Stations with weak signal can only be tuned in manually.
4.
Use the ‘P-MODE/MONO’ button to select stereo or mono broadcasting.