Filter
Top Products
OPERATING / TROUBLESHOOTING 7
Operating Instructions
Listening to your CD player, tape
deck, tuner or other source
1.Turn Volume control to minimum level and
press the flat Power switch to turn on the
amplifier.The power indicator lights blue and
the protection circuitry checks for short circuit
or other problems for a few seconds before
sound output.
2. Press ”Speaker 1” to hear loudspeakers
connected to the rear Speakers 1 terminals.
Press ”Speaker 2” to hear loudspeakers
connected to the rear Speakers 2 terminals.
Press both to hear both speaker pairs at once.
To listen to headphones only, press to turn off
any active speaker pair.
3. Select desired source for listening by pressing
the front panel Source up or down repeatedly
until the name of the source is shown in the
Main Information Display or by pressing the
desired Source button on the remote control.
4. Begin playing the desired source.
5.Adjust the Volume control to the desired level.
6.Adjust Bass,Treble and Balance controls as
desired (the Source Direct function must be
turned off).To adjust the bass level, press the
Mode Button twice so that the Main Informa-
tion Display shows
BASS0dB. By turning
the Volume Button to the right, the bass level
will increase, turning the Volume Button left
will decrease the bass level.
Once the desired bass level has been set, press
the Mode Button to set the requested level for
the treble.The Main Information Display will
show
TREBLE0 dB. By turning the Volume
Button to the right, the treble level will increase,
turning the Volume Button left will decrease the
treble level.
Once the desired treble level has been set, press
the Mode Button to set the requested level for
the balance.The Main Information Display will
show
BALANCE0. By turning the Volume
Button to the right, the balance will move to the
right speaker, turning the Volume Button left will
move the balance to the left speaker.
Press the Mode Button again to return the the
normal volume indication.
7. Press ”Source Direct” until the the Main Infor-
mation Display shows
DIRECT ONto
bypass the tone control to ensure purest
sound performance. Press again to turn the
bypass function off and to make the tone and
balance controls function again.
Making a recording
You may record any source to tape or to CD-R or
to both simultaneously.You may also connect a
second tape deck to the CDR inputs and outputs
to record from tape to tape (in either direction).
To select the desired source for recording (this
can be a different source than the one being
listened to), press the Record Source Selector up
or down button on the front panel repeatedly
until the indicator for the name of the source to
be recorded is shown in the Main Information
Display.
NOTE: The record output signal is taken directly
from the program source and is unaffected by
the Volume, Bass,Treble or Balance controls.
Important Notes:
• The functions ”Source Direct” and ”Record
Source” can be selected on the front panel
only, not from the remote control.
• 3-head cassette decks with monitoring func-
tion can be connected to ”Tape” or ”CDR”
connectors too, but their monitoring function
cannot be used.
Troubleshooting
This unit is designed for trouble-free operation; most problems users encounter are due to operating errors. So if you have a problem, first check this list for a
possible solution. If the problem persists, consult your authorized Harman Kardon service center.
If the problem is... Make sure that...
No lights illuminate when power cord is plugged into AC outlet. • The unit is plugged into a live outlet.
No sound is heard. • Speaker switches corresponding to the desired speakers are pressed.
• Correct source button has been pressed.
• Volume is turned up.
• Speaker wires are connected properly.
• Hook-up wires to source component are connected properly.
Sound is not heard from the speaker system on one side. • The speaker wires and connection wires are connected correctly.
• Set the balance setting to 0
When listening to stereo sound, the left and right sounds are reversed. • The speaker wires are connected correctly.
• The wires between components are connected correctly.
Intermittent or continuous buzzing or hissing. • The unit is away from fluorescent lights, TV, motors and other electrical appliances.
The remote control and front panel controls don't appear to work. • Disconnect the AC line cord from the wall socket, wait 5 minutes and then re-connect it.
Humming noise when listening to LP • Ground wire from record player has been connected to ground terminal on amplifier.
• Cable from record player is away from power cords and speaker cables.
Howl or ringing when listening to LP. • Record player is not to close to speakers.
• Record player is on stable surface.
Low sound level when listening to LP. • Cable from record player is connected to the Phono jacks.
• The phono cartridge is MM, not MC.