Filter
Top Products
(5)
EXIT/RETURN: Press loop EXIT/RETURN (21) to return to the beginning
of the previously saved loop from normal play.
PITCH: Pushing the PITCH BUTTON (22) activates the PITCH CONTROL
SLIDE (35). The pitch of the CD will change according to the position of
the PITCH CONTROL SLIDE (23).
PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (23) will
automatically raise the pitch up to +4% or lower the pitch down to -4%
from the existing pitch setting. Releasing the buttons will return the pitch
to the original pitch setting. You can use this function to match the pitch
bend when mixing from one song to another.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (24) up
or down will lower or raise the pitch percentage.
OPERATIONS:
1. Press the OPEN/CLOSE (8) button, place a CD in the DISC TRAY (7)
and press the OPEN/CLOSE (8) button again. The tray will close into the unit.
2. Push the TRACK (13) buttons to select the track you want to play.
3. Press the PLAY/PAUSE (11) buttons and the unit will instantly play.
CUES:
FLY CUE:
The FLY CUE function lets you set cues “on the fly” with the press of
a button. Press FLY CUE when the disc reaches the musical location
you wish to make your cue or start point. The cue point is now
programmed. Press CUE to return to the cue point. Press PLAY/PAUSE
and the unit instantly starts from this pre-programmed spot.
PLAY CUE:
1. To pre-program a cue point (the spot on a CD at which you want play to
start) select the proper track and push PLAY/PAUSE so the unit enters
the PLAY mode. (PLAY/PAUSE LED glows green).
When the CD reaches the approximate musical spot you wish to make
your cue, push PLAY/PAUSE so the unit enters the PAUSE mode (PLAY/
PAUSE LED blinks). Move the SEARCH DIAL forward or in reverse
until the precise spot at which you want CD play to begin is located. Push
PLAY/PAUSE. The cue point is now programmed. Press CUE to return
to this pre-programmed cue point at any time. Push PLAY/PAUSE and
the unit will instantly play from the pre-selected spot.
2. To fine tune your pre-programmed cue point, push PLAY/PAUSE
so the unit enters the PLAY mode. Push the CUE button and the
CD will return to the cue point you programmed in step #1 and
begin play from that point. If you decide this cue or starting point
is okay, leave the unit alone until you are ready to play.
3. If, however, the selected spot is not exactly where you want it, push the
CUE button while the CD is playing and the disc will return to the pre-
programmed cue point. Locate the exact spot on the CD at which you
want play to start by turning the SEARCH DIAL. Push PLAY/PAUSE to
pre-program this new cue point. Press the CUE button to pause play at
the new cue point. Push PLAY/PAUSE at any time and the unit will play
from the pre-selected spot.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND
THE BEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS THE PLAY/PAUSE
(11) TO SAVE THE CUE POINT.
TROUBLESHOOTING:
• If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
• If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
• If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
SPECIFICATIONS:
GENERAL:
Type.............................................................................Compact Disc Player
Disc Type.......................................Standard Compact discs (12 cm & 8 cm)
Time Display...........................Track Elapsed, Track Remain, or Total remain
Variable Pitch............................................± 12% Slider with Resume Switch
Pitch Bend..........................................................................± 16% Maximum
Instant Start...................................................................Within 0.03 seconds
Track Selection.......................................................................1 to 99 Tracks
Installation.......................................................................................19" each
Dimensions...........................................................................19” x 3.5” x 10”
Weight Per Unit.................................................................................9.5 lbs.
AUDIO SECTION:
Quantization..........................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate...........................................................................8 Times
Sampling Frequency........................................................................44.1 kHz
Frequency Response...........................................................20 Hz to 20 kHz
Digital Output.....................................................................................IEC958
Total Harmonic Distortion...................................................Less Than 0.05%
Signal to Noise Ratio..........................................................................104 dB
Dynamic Range...................................................................................98 dB
Channel Separation.................................................................90 dB (1 KHz)
Output Level........................................................................1.9 Volts R.M.S.
Power Supply............................................................AC 115/230V, 60/50 Hz
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
IN THE USA: IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT, PLEASE CALL 1 (732) 738-9003 FOR
GEMINI CUSTOMER SERVICE. DO NOT ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER.