Filter
Top Products
the CONTINUOUS function causing the unit to play continuously (after
the last track, the unit will return to the first track of the disc and continue
to play). Pressing the SINGLE (19) button a third time deactivates the
CONTINUOUS function.
TIME/OUTRO: The TIME BUTTON (17) switches the time display
between the 4 available choices listed under DISPLAY (12). This also
swithces on/off the Outro function, which only plays the last 30 seconds
of each track.
PITCH: Pushing the PITCH BUTTON (20) activates the PITCH CON-
TROL SLIDE (21). The pitch of the CD will change according to the posi-
tion of the PITCH CONTROL SLIDE (21).
PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS
(22) will automatically raise the pitch up to +16% or lower the pitch down
to -16% from the existing pitch setting. Releasing the buttons will return
the pitch to the original pitch setting. You can use this function to match
the pitch bend when mixing from one song to another.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (21)
up or down will lower or raise the pitch percentage.
OPERATIONS:
1. Press the OPEN/CLOSE (8) button, place a CD in the DISC TRAY
(7) and press the OPEN/CLOSE (8) button again. The tray will close into
the unit.
2. Push the TRACK SKIP(14) buttons to select the track you want to
play.
3. Press the PLAY/PAUSE (10) buttons and the unit will instantly play.
CUES:
1. To program a cue point (the spot on a CD at which you want play to
start) select a track and push PLAY/PAUSE (10) so the unit enters the
PLAY mode. (PLAY/PAUSE LED glows green).
2. When the CD reaches the approximate musical spot you wish to
make your cue, push PLAY/PAUSE (10) so the unit enters the PAUSE
mode (PLAY/PAUSE LED blinks and the unit will enter stutter mode).
Move the SEARCH DIAL (9) forward or in reverse until you reach the
precise frame is located, at which point you will want the CD to begin
play. Push CUE (11). The cue point is now programmed, the blue LED
will remain on. Press and hold CUE (11) to preview the cue point.
Release CUE (11) to return to the cue point. Press CUE (11) to return to
this pre-programmed cue point and play at any time.
Note: Once you have skipped to another track, you may not go back to your programmed
cue point. You must begin your cue selection over again once you have skipped to anoth-
er track. The cue will be preset to the beginning of the selected track. Press the cue but-
ton and you will begin at the beginning of your selected track. Start your Cue program-
ming sequence over again.
3. To fine tune your pre-programmed cue point, push the CUE (11) but-
ton and the CD will return to the cue point you programmed in step #2.
Push PLAY/PAUSE (10) so the unit enters the PAUSE mode at that
point. Use the SEARCH DIAL (9) to move forward or backward to find
the proper Cue point. Repeat step #2. If you decide this cue or starting
point is okay, leave the unit alone until you are ready to play.
4. If, however, the selected spot is not exactly where you want it, push
the CUE (11) button while the CD is playing and the disc will return to
the preprogrammed cue point. Repeat step #1 - #3.
NOTE: During fine tuning there will be a stutter effect (to help you find the beat). The stut-
tering effect will end when you press the PLAY/PAUSE (10) to save the cue point.
TROUBLESHOOTING:
· If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
· If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
· If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
SPECIFICATIONS:
GENERAL:
Type.................................................................................Compact Disc Player
Disc Type...........................................Standard Compact discs (12 cm & 8 cm)
Time Display..............................Track Elapsed, Track Remain, or Total remain
Variable Pitch...............................................± 16% Slider with Resume Switch
Pitch Bend..............................................................................± 16% Maximum
Instant Start.......................................................................Within 0.03 seconds
Track Selection...........................................................................1 to 99 Tracks
Installation...........................................................................................19" each
Dimensions..............................................................................19” x 3.5” x 10”
Weight (total)......................................................................10.21 lbs. (6.21 Kg)
AUDIO SECTION:
Quantization.............................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate...............................................................................8 Times
Sampling Frequency...........................................................................44.1 kHz
Frequency Response..............................................................20 Hz to 20 kHz
Digital Output........................................................................................IEC958
Total Harmonic Distortion......................................................Less Than 0.05%
Signal to Noise Ratio...............................................................................85 dB
Dynamic Range.......................................................................................85 dB
Channel Separation.................................................................................85 dB
Output Level.......................................................................2.0 +/- 0.2V R.M.S.
Power Supply...............................................................AC 115/230V, 60/50 Hz
Specifications and design are subject to change without notice for purpose of improvement.
(5)