Filter
Top Products
CVDA 6 EQ MX • Installation
Installation
1
Front Panel Controls and Indicators
2CVDA 6 EQ MX • Front Panel Controls and Operations1
Description
Extron’s CVDA 6 EQ MX is a 1-input, 6-output composite video
distribution amplifier with level adjustment and equalization
capabilities and a buffered loopout. The adjustments can equalize a
video signal up to 500 feet away on high quality cable such as Extron
SuperFlex SHR Super High resolution coaxial cable. The buffered
loopout is not equalized and is appropriate for connecting a second
CVDA 6 EQ MX or a local monitor.
The CVDA 6 EQ MX is rack mountable and has an internal auto-
switchable power supply that can accept 100VAC to 240VAC at 50 Hz to
60 Hz.
Installation and Rear Panel Connections
1. For optional rack mounting, mount the CVDA 6 EQ MX unit on
the left or right side of a 19" 1U Universal Rack Shelf (Extron
P/N 60-190-01) (figure 1).
4-40 X 1/8 Screws
Use 2 Mounting Holes
on Opposite Corners
False Front Panel
Uses 2 Front Holes Only
C
V
D
A
6
E
Q
M
X
COM
POS
ITE VID
EO DISTR
IBU
TIO
N/EQUALIZATION
A
MPL
IFIER
CVDA 6 EQ MX
COMPOSITE V
IDEO DISTRIBU
TIO
N/EQUALIZATIO
N AM
PLIFIER
L
E
V
E
L
E
Q
U
A
L
I
Z
E
MAXMIN
L
E
V
E
L
E
Q
U
A
L
I
Z
E
M
A
X
M
IN
Figure 1 — Rack mounting the CVDA 6 EQ MX
a. If feet were previously installed on the bottom of the case,
remove them.
b. Mount the CVDA 6 EQ MX on the rack shelf, using two
4-40 x 1/8 screws in opposite (diagonal) corners to secure the
case to the shelf.
2. Connect the composite video input to the input BNC connector on
the rear of the CVDA 6 EQ MX (figure 2).
3. Connect the desired devices to the composite video output BNCs
on the rear of the CVDA 6 EQ MX.
4. Connect power to the CVDA 6 EQ MX.
OUTPUTS
INPUT
BUFFERED
LOOP-OUT
100-240V 50-60Hz
0.35A
123456
CVDA 6 EQ MX
Projector
MonitorDVD player
CVDA 6 EQ MX
Up to 6
outputs
LEVEL EQUALIZE
MAXMIN
COMPOSITE VIDEO DISTRIBUTION/EQUALIZATION AMPLIFIER
CVDA 6 EQ MX
VCR
Figure 2 — Typical CVDA 6 EQ MX application
Front Panel Controls and Operations
1
Power LED — This LED (figure 3) lights to indicate that the
CVDA 6 EQ MX is receiving power.
Operation — After the CVDA 6 EQ MX and its connected devices
are powered up, the system is fully operational. If any problems
are encountered, verify that the cables are routed and connected
properly.
LEVEL EQUALIZE
MAXMIN
COMPOSITE VIDEO DISTRIBUTION/EQUALIZATION AMPLIFIER
CVDA 6 EQ MX
1 2 3
Figure 3 — CVDA 6 EQ MX front panel
2
Level adjustment — This control is similar to a TV’s brightness
control. The level adjustment compensates for signal amplitude
losses caused by cable resistance. The control adjusts the
composite video output signal gain, through one full turn, from -
6dB through +6dB.
Operation — With a waveform monitor connected to the far end
of one of the output cables, adjust the level so that the level is
100 IRE.
If no waveform monitor is available, adjust the level to boost the
level to achieve the best possible image.