Filter
Top Products
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other International locations. For customer orders, contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 736-4212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 5/2005
Part Number 38110-470 Rev. 1
Dimension Drawings:
ZX1i Part Numbers
• 301851-001 - ZX1i-90, 90° x 50° Horn, Black Finish
• 301851-002 - ZX1i-90W, 90° x 50° Horn, White Finish
• 301851-003 - ZX1i-100, 100° x 100° Horn, Black Finish
• 301851-004 - ZX1i-100W, 100° x 100° Horn, White Finish
• 301852-001 - ZX1i-100T, 100° x 100° Horn, Black Finish, Transformer
• 301852-002 - ZX1i-100TW, 100° x 100° Horn, White Finish, Transformer
Performance Match
• D170180 CPS2T, 120V Power Amplifier, 2 x 600W
• D170261 CPS2.8, 120V Power Amplifier, 2 x 800W
Accessories
• 301918-001 AB-ZX1i, Array Bracket Kit for 2 or 4 Systems,
Black
Front View
Top View
Right View
This ZX1i Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the
ZX1 Users Manual
and possible manual update notices. This system should be suspended with certified rigging hardware by an
authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.
CAUTION
Block Diagrams:
Architectural and Engineering Specs:
ZX1i (Non-Transformer) and ZX1i-100T in 8Ohm Mode ZX1i-100T
The loudspeaker shall be a two-way system consisting of one 8"” (102mm) low-
frequency transducer, 1" (25mm) high-frequency true compression driver with rotatable
horn, and frequency dividing network installed in a vented enclosure. The network
shall include a passive limiter for both the low frequency and high frequency
transducers. The high frequency compression transducer shall drive a horn to evenly
cover a pattern of either 90° by 50° or 100° by 100°. The horn shall be rotatable to
allow for horizontal or vertical mounting of the cabinet. The enclosure shall be molded
of high impact polystyrene.
The finish shall be a paintable black or white. The grille shall be zinc plated, powder
coated for corrosion resistance, and equipped with both hydrophobic cloth and acoustic
foam. The loudspeaker position shall be adjustable over a range of 100° horizontally
and 45° vertically.
The support bracket shall be low profile and integral with the enclosure. The bracket
shall allow for a quick snap fit mounting of the speaker enclosure for placement
before securing. The speaker terminals shall include a 4 pin removable phoenix style
connector to allow for signal pass through. The system shall be weather resistant to
MIL Spec 810 and IEC 529 test conditions.
The loudspeaker shall be available with a 100w transformer for 70 or 100v operation.
The speaker shall have ASC
TM
for transformer saturation protection against overload.
Their also shall be an 8 ohm bypass position on the wattage selector switch to enable
8 ohm operation from these models.
The loudspeaker system shall meet the following performance criteria: Power handling,
200-Watts long term program using IEC268-5 shaped pink noise; Frequency response,
48 Hz – 20 kHz (-10 dB from rated sensitivity); Pressure sensitivity, 94 dB at one
watt, 60 Hz – 20 kHz at one meter; Impedance, 8 ohms nominal, 6 ohms minimum.
The enclosure shall be 17.75" (451mm) high, 11.12" (282mm) wide, 10.35" (263mm)
deep. Net weight shall be 18.5 lbs (8.4 kg) for non-transformer versions and 23.0 lbs
(10.4 kg) for transformer versions.