Filter
Top Products
SPECIFICATIONS AS660e
DIMENSIONAL DRAWING
A & E SPECIFICATIONS
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX 508 234 8251 info@eaw.com www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. AS660e/2 pp October 2001 Printed in USA
Dimensions inches millimeters
Height 36.0 914
Width (Front) 24.6 626
Width (Rear) 12.3 312
Depth 23.0 584
Trapezoid Angle 15 degrees per side
Weights pounds kilograms
Net Weight 169 76.9
Shipping Weight 184 83.7
The bi-amplified or tri-amplified 3-way full range loudspeak-
er system shall incorporate 2x 12-in vented LF transducers, a
horn-loaded 10-in MF cone with Radial Phase Plug™ and a
1.4-in exit/2.5-in voice coil HF neodymium compression driver
.
The LF drivers shall be mounted in slanted baffles and sepa-
rated vertically. The MF driver shall be loaded into a midrange
horn constructed of 1/8-in birch plywood backed with high
density polyurethane foam. The HF driver shall be loaded on
a constant directivity horn with a nominal coverage pattern
of 60° (h) x 45° (v). An internal passive filter network shall
provide fourth order acoustical crossover and system equal-
ization between the MF and HF subsystems.
System frequency response shall vary no more than ±3 dB
from 67 Hz to 15 kHz measured on axis. The mid/high section
shall produce a Sound Pressure Level (SPL) of 107 dB SPL on
axis at 1 meter with a power input of 1 Watt, and shall be
capable of producing a peak output of 139 dB SPL on axis at
1 meter. The low frequency section shall produce a Sound
Pressure Level (SPL) of 102 dB SPL on axis at 1 meter with a
power input of 1 Watt, and shall be capable of producing a
peak output of 137 dB SPL on axis at 1 meter. The mid fre-
quency section shall produce a Sound Pressure Level (SPL) of
109 dB SPL on axis at 1 meter with a power input of 1 Watt,
and shall be capable of producing a peak output of 141 dB
SPL on axis at 1 meter. The high frequency section shall pro-
duce a Sound Pressure Level (SPL) of 109 dB SPL on axis at 1
meter with a power input of 1 Watt, and shall be capable of
producing a peak output of 136 dB SPL on axis at 1 meter.
The mid/high section shall handle 450 Watts of amplifier
power (continuous) and shall have a nominal impedance of 8
Ohms. The low frequency section shall handle 800 Watts of
amplifier power (continuous) and shall have a nominal
impedance of 4 Ohms. The mid frequency section shall han-
dle 400 Watts of amplifier power (continuous) and shall have
a nominal impedance of 8 Ohms. The high frequency section
shall handle 125 Watts of amplifier power (continuous) and
shall have a nominal impedance of 8 Ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It
shall be constructed of multi-ply, void-free, cross-grain-lami-
nated, exterior grade, Baltic birch plywood and shall employ
extensive internal bracing. It shall be finished in wear-resist-
ant textured black paint. Input connectors shall be 2x 6-con-
tact terminal strips, jumpers used for powering configuration.
Eighteen (18) 3/8"-16 threaded mounting/suspension points
(4 each on top, bottom and sides, 2 on back) shall be pro-
vided. The front of the loudspeaker shall be covered with a
powder coated perforated steel grille.
The bi-amplified or tri-amplified 3-way full range loudspeak-
er shall be the EAW model AS660e.
509132 (0)
5/10/01
INDICATES MOUNTING POINT, 3/8-16 THREADED HOLE
(PI ANGLE).
INDICATES MOUNTING POINT, 3/8-16 THREADED HOLE
(NUT PLATE).
SYMBOL INDICATES CENTER OF BALANCE.
FRONT
36.00
24.63
GRILLE PARTIALLY SHOWN
BACK
L
C
5.00
L
C
ACCESS
PANELS
INPUT
18.88
(1.50)
4.00
33.00
4.00
A
A
L
C
23.00
16.00
12.00
(12.29)
10.09
18.67
30¡
TOP/BOTTOM
30°
16.56
L
C
4.63
32.10
SIDE VIEW (VIEW A-A)
DIMENSIONS APPLY TO BOTH SIDES
Manufacturing tolerances are +/- 0.13 and +/- 1°