Filter
Top Products
Model
Revc. (Ohms)
Fo. (Hz)
Sd. (msqM)
BL. (TM)
Qms.
Qts.
SPLo. (dB)
Vas. (Ltr)
Xmax (mm)
(Xmax Measured In One Direction)
Qes.
SWS-6.5X
3.600
39.31
12.500
4.350
4.192
1.723
1.221
77.3
9.94
15
27.830
23
SWS-8X/8Xi
3.500
30.394
22.000
6.210
3.987
0.804
0.669
86.7
51.479
28
SWS-10X
3.700
28.477
33.000
22.095
5.02
0.51
0.46
88.2
149.612
31
SWS-12X
3.700
24.006
53.000
10.642
3.56
0.515
0.45
89.4
203.112
34
SWS-15X
3.400
21.006
89.000
10.956
3.847
1.02
0.65
90.4
Congratulations are in order... You are now the proud owner of an SWS Shallow Mount
Woofer: the most advanced
shallow woofer technology to hit car and home audio. The idea is simple: to generate deep
bass from the shallowest space. For years, audio manufacturers attempted to reduce the
mounting depth of a driver; nevertheless the speaker size/diameter still played a major role
in dictating the mounting depth. Approximately, a speaker mounting depth remained to be
about ½ the size of the speaker diameter: the larger the speaker the deeper the mounting
depth.
Audio, video, and data processing components have gotten better, faster and smaller. This
is true except when it
comes to speakers design, conventionally designed drivers remain “bulky” in comparison to
other audio components. In 1929, Mr. H. Shotwell designed the first “front loaded magnet”
driver, it was a small step in reducing the mounting depth of driver. Since then, other audio
manufacturers (such as Bose, Harmon and others) made several attempts to reduce the
mounting depth of a driver. Nevertheless, the speaker mounting depth remained to be
about roughly half the size of the speaker diameter - the larger the speaker the deeper the
mounting depth. This “handicap” held true until few years ago when Joseph J. Sahyoun
(Vice President, Inventor, and Head Engineer at Earthquake Sound Corporation) started
developing the shallow mount woofer system (SWS). The “SWS” presented a radical
solution away from the conventional “bulky” speaker design.
The SWS design reduces the mounting depth of a speaker by over 60% without taxing its
performance. These
numbers look even better as the speaker diameter increases. A conventional 12” woofer
has a mounting depth of 6 to 7 inches (for a ± 1” excursion); on the other hand, an SWS-12
performs the same in a little less than 3” of mounting depth. The SWS design allows the
installer to use compact enclosures, whereby the mounting depth is about 1.5 times the
peak-to-peak excursion. The SWS technology makes the speaker mounting depth
“excursion-dependent” and not “diameter-dependent”. Once a target Xmax is set, the
mounting depth follows (1.5 times the peak to peak excursion); the Xmax remains
independent from the size (diameter) of the speaker. The SWS opens the door for
unrestricted bass applications where a conventional subwoofer could never be used.
In home applications, SWS allows the designer to build 12” in wall woofer that moves 2”
peak to peak while
maintaining a mounting depth of less than 3”. This technology opens the door for home
theater designers to squeeze large woofers in very tight spaces / closets, also to do in-wall
woofer application. In car applications, rear-deck subwoofer mount - used by manufacturers
of luxury automobiles- represents a prefect example of a totally stealth install (using 10”,
12”, 15” SWS). 8” door mount with 1” peak to peak now is possible where mounting depth
is a mere 1.5”; with a possibility of using 10” SWS in the doors of larger SUV's.
The aluminum custom-made cone and dust cap are designed to reduce the voice coil
temperature by dissipating the
heat that builds up in the voice coil. The dust cap is directly fastened to the voice coil
aluminum bobbin, it transfers the heat build-up from the bobbin into the cone. Both dust cap
and cone act as a giant heat sink to reduce the voice coil temperature and increase its
power handling and endurance. The high roll pressed-foam surround is coupled with a
propagating spider to allow for extreme excursions with no limitations. The slick shallow
basket is coated with black chrome and is shaped with slant edges for easy install in tight
spaces.
DEAR VALUED CUSTOMER
www.earthquakesound.com
SWS PARAMETERS
NOTE: The 2-Ohm SWS-8Xi is designed to replace subwoofer in factory
upgraded vehicles, such as BMW's, Corvettes, Mercedes Benz and
much more.
2 3
All Specifications Are Subject To Change Without Notice