Filter
Top Products
10
ENGLISH
q
Track, minute, second and frame
displays
• These displays indicate current position
information.
w
Loop mode indicat
ors
• DN-S3000 has Loop mode indicators which
consist of A , B and two arrows. A and B marks
indicate A and B points are exist.
• Two arrows indicate loop setting mode as
follow.
or Left arrow only on:
Hot Start mode
Both arrows on:
Seamless Loop mode
, Both arrows flashing:
Seamless Loop Playing
,
Left arrow on, right flashing:
Exit play from Seamless Loop
e
Time mode indicators
• When the TIME/T.TIME button is pushed, the
Time mode indicator switches as follows:
ELAPSED:
Track’s elapsed time is displayed.
REMAIN:
Track’s remaining time is displayed.
TOTAL + ELAPSED:
The total elapsed time of disc is displayed.
TOTAL + REMAIN:
The total remaining time of disc is displayed.
BA1
BA1
BA1
BA1
BA1
BA1
BA1
r
Parameter indicators
(upper 30 dots)
• Upper 30 dots on display indicate parameter,
data setting for Effector.
t
Character display
• You can select mode or function using
PARAMETERS knob following the short
message which is displayed on the character
display part.
• The character display indicates the operation,
mode name, data, etc., and displays such
guide messages as “Yes/Push_PM” means if
“YES”, push PARAMETERS knob. The display
indicates and marks sometime, note
that mark says you to turn PARAMETERS
knob and marks says to push
PARAMETERS knob.
• The PARAMETERS LED flashes when you can
use PARAMETER knob, otherwise this knob
used for Track Selection.
y
Play mode indicators
• When SINGLE indicator lights up, playback will
finish at end of current track.
• When CONT. indicator lights up, playback
continues.
u
KEY ADJ. indicator
• KEY ADJ. indicator appears in display when in
the Key Adjust mode.
i
MEMO indicator
• MEMO indicator appears in display when
there is a memo setting for the currently
playing track or the track at which the standby
mode is currently set.
sm
CONT.
f
SINGLEREMAIN
s
m
TOTAL
BA1
ELAPSED
DRAG S.
DUMP
BRAKE
RVS
KEY ADJ.
MEMO
w uye trq
!0
!1
t
o
i
(4) Display
o
Play Position indicators
(lower 33 dots)
• Play position indicator:
The 33 white dots indicate where is playing
visually in a track in the normal play. The 11
Orange dots indicate play position in the
reverse play mode.
• End of Message:
When the time remaining to the end of the
track is less than the specified time, the EOM
(End Of Message) play position indicator
flashes along with the remaining time,
notifying of the track end.
✽ The EOM time can be set in the presets.
!0
Pitch display
• This indicator display the playback speed
(pitch).
!1
PLATTER MODE indicators
• There are indicators for all Platter Effects
DRAG-S., BRAKE, DUMP and RVS. These
indicators light up when each mode is on.
4
COMPACT DISCS
1. Precautions on handling compact discs
• Do not allow fingerprints, oil or dust to get on the
surface of the disc.
If the disc is dirty, wipe it off with a soft dry cloth.
• Do not use benzene, thinner, water, record spray,
electrostatic-proof chemicals, or silicone-treated
cloths to clean discs.
• Always handle discs carefully to prevent
damaging the surface; in particular when
removing a disc from its case or returning it.
• Do not bend the disc.
• Do not apply heat.
• Do not enlarge the hole in the center of the disc.
• Do not write on the label (printed side) with a
hard-tipped implement such as a pencil or ball
point pen.
• Condensation will form if a disc is brought into a
warm area from a colder one, such as outdoors
in winter. Do not attempt to dry the disc with a
hair dryer, etc.
2. Precautions on storage
• After playing a disc, always unload it from the
player.
• Always store the disc in the jewel case to protect
from dirt or damage.
• Do not place discs in the following areas:
(1) Areas exposed to direct sunlight for a
considerable time.
(2) Areas subject to accumulation of dust or high
humidity.
(3) Areas affected by heat from indoor heaters,
etc.