Filter
Top Products
50 Spring Street, Ramsey,NJ 07446, U.S.A.
Tel. 201-934-8500, Fax: 201-934-9832, www.bogen.com
The RE84 and TB8 are warranted to be free from defects in material or workmanship
for two (2) years from the date of sale to the original purchaser. Any part of the prod-
uct covered by this warranty that, with normal installation and use, becomes defec-
tive will be repaired or replaced by Bogen, at our option, provided the product is
shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring
Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid.
This warranty does not extend to any of our products that have been subjected to
abuse, misuse, improper storage, neglect, accident, improper installation or have
been modified or repaired or altered in any manner whatsoever, or where the serial
number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE
WARRANTY AND THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS
OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITYOR FIT-
NESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND
EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability
arising out of the manufacture, sale or supplying of products or their use or disposi-
tion, whether based upon warranty, contract, tort or otherwise, shall be limited to the
price of the product. In no event shall Bogen be liable for special, incidental or con-
sequential damages (including, but not limited to, loss of profits, loss of data or loss
of use damages) arising out of the manufacture, sale or supplying of products, even
if Bogen has been advised of the possibility of such damages or losses. Some States
do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from State to State.
Products that are out of warranty will also be repaired by the Bogen Factory Service
Department -- same address as above or call 201-934-8500. The parts and labor
involved in these repairs are warranted for 90 days when repaired by the Bogen
Factory Service Department. All shipping charges in addition to parts and labor
charges will be at the owner's expense. All returns require a Return Authorization
number.
Limited Warranty
1. Place ceiling tile with the finished side facing up over a large
trash can (provides support and saves clean up time).
2. Cut hole in the center of the ceiling tile using the raw speaker
as a template.
3. Position the tile bridge on the unfinished side of the ceiling tile
and bend (4) locator tabs into tile opening to prevent sliding.
4. Install Ceiling Speaker assembly using (4) 8-32 screws and
the threaded holes of the tile bridge as shown. (Screws are
provided with Ceiling Speaker assembly).
1. Place ceiling tile with the finished side facing up over a large
trash can (provides support and saves clean up time).
2. Cut hole in the center of the ceiling tile using the raw speaker
as a template.
3. Bend (4) horseshoe tabs up on tile bridge.
4. Position the tile bridge on the unfinished side of the ceiling tile
and bend (4) locator tabs into tile opening to prevent sliding.
5. Slip seismic mounting tie-off tabs (2) through RE84 tie-off tab
slots until they click into place and secure customer-supplied
“tie-off” wire to tab.
6. Punch out knockout in the RE84 and install Listed metallic
enclosure entry fitting to knockout to accommodate plenum
cable or plenum whip and feed cable or whip through the
knockout.
7. Install RE84 to tile bridge by orienting horseshoe tab slots (4)
over horseshoe tabs (4) of bridge.
8. With pliers, twist horseshoe tabs (4) of tile bridge 1/2 turn,
securing enclosure to bridge.
9. Screw the Ceiling Speaker assembly to the RE84 using (4)
8-32 screws provided with the Ceiling Speaker assembly,
sandwiching the TB8 and ceiling tile in between. The screws
must go through the TB8 clearance holes as shown. (Screws
anchor into the RE84).
TB8 with RE84 InstallationTB8 Installation