All power ratings conform to CEA-2006 standards.
PARAMETER/FEATURE PCA 260 PCA 2120
Channels 2/1 2/1
Size ( W x H x D) 10x1.9x8.5 inches (254x49x215mm) 10x1.9x11.6 (254x49x295mm)
Weight 4.8 lbs (2.2 kg) 5.6 lbs (2.5 kg)
Spade screw speaker terminals? YES YES
Maximum terminal wire size 14 ga. 14 ga.
Subsonic filter YES (10 Hz) YES (10 Hz)
Separate front/rear or left/right gains? NO NO
Fuse Type ATC spade -30A ATC spade -Two 25A
Speaker short, short to +12V, and short to ground protection? YES YES
High, low, and reverse voltage protection? YES YES
Power output transistors BTL BTL
Power supply transistors MOSFET MOSFET
Minimum speaker impedance (non-bridged) 2 ohms 2 ohms
(bridged) 4 ohms 4 ohms
PERFORMANCE DATA
Rated power output @ 0.1% THD, 14.4V (CEA-2006)
2 channels into 4 ohms / 2 ohms (watts rms) 2 x 60 W / 2 x 80 W 2 x 120 W / 2 x 180 W
1 channel into 4 ohms (watts rms) 1 x 150 W 1 x 300 W
Max Dynamic Power (watts rms) 200W 350W
Total Harmonic Distortion @ full power 0.1% THD 0.1% THD
Signal/Noise ratio (gain controls in center)
Measured @ 1 watt / 1 kHz dBA >80 >80
Measured @ full rated power (0.1% THD) dBA >97 >101
Damping factor >100 >100
Frequency response (full-range mode) 20 - 30,000 Hz 20 - 30,000 Hz
High-pass crossover frequency limits 50 H z - 250 Hz (variable), 12dB/oct 50 H z - 250 Hz (variable), 12dB/oct
Low-pass crossover frequency limits 50 H z - 250 Hz (variable), 12dB/oct 50 H z - 250 Hz (variable), 12dB/oct
Bass Boost Variable (0-12dB) Variable (0-12dB)
Input impedance 10 kohms 10 kohms
Input signal voltage control range 0.3 - 6.0 vrms 0.3 - 6.0 vrms
Current Draw @ 13.8 VDC (typical values @ X watts / Efficiency %)
@ full rated power, unbridged (@ 4 ohms) 17 A (50%) 30 A (52%)
@ 33% rated power, unbridged (@ 4 ohms) 9 A (35%) 15 A (50%)
@ idle (@ 4 ohms) 1.5 A 2 A
Minimum battery voltage to maintain rated power 13.8 VDC 13.8 VDC
Usable battery voltage 10 - 16 VDC 10 - 16 VDC
Trigger line voltage range 10 - 16 VDC 10 - 16 VDC
Trigger line current draw < 10 mA < 10 mA
Turn on delay time @ 2.0 seconds @ 2.0 seconds
Thermal shutoff temperature (average heat-sink temp) @ 85˚ C (185˚ F) @ 85˚ C (185˚ F)
NOTE: DUE TO ONGOING PRODUCT IMPROVEMENTS, DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE
WITHOUT ADVANCED NOTICE TO THE CONSUMER OR RETAILER.
B
LAUPUNKT
S
PECIFICATIONS
- PCA 260 & PCA 2120, 2/1 C
HANNEL
A
MPLIFIERS
www.midwestelectronics.com