Audio-Technica BP892 & BP892-TH Headphones User Manual


  Open as PDF
of 2
 
BP892 & BP892-TH
Specications
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
12" or more on axis
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50
200
10k
5k
1k
500
2k
20k
Roll-off
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
12" or more on axis
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50
200
10k
5k
1k
500
2k
20k
Roll-off
frequency response: 20–20,000 Hz polar pattern
Fixed-charge back plate, permanently
polarized condenser
Omnidirectional
20-20,000 Hz
80 Hz, 18 dB/octave (wired only)
–49 dB (3.5 mV) re 1V at 1 Pa
250 ohms (wired only)
135 dB SPL, 1 kHz at 3% T.H.D.
104 dB, 1 kHz at Max SPL (wired only)
63 dB, 1 kHz at 1 Pa
11-52V DC, 2 mA typical (wired only)
0.1 mA typical at 5V (wireless only)
2.5-11V (wireless only)
Flat, roll-off (wired only)
Microphone, boom & earpiece:
2.6 g (0.09 oz)
Power module (wired only): 85 g (3.0 oz)
Microphone: 8.1 mm (0.32") long,
2.6 mm (0.10") diameter
Boom: 98.4 mm (3.87") long,
1.07 mm (0.04") diameter
Power module (wired only): 97.6 mm
(3.84") long, 18.9 mm (0.74") diameter
Integral 3-pin XLRM-type
1.4 m (55") long (permanently attached
to microphone), 1.6 mm (0.06") diameter,
2-conductor shielded cable with locking
4-pin connector (wired only)
M31
AT8539 power module (wired only);
AT8440 cable clip; AT8464 dual-ear
mount; two AT8157 windscreens; two
AT8156 element covers; moisture guard;
belt clip (wired only); carrying case
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio
1
Phantom power requirements
Current consumption
Voltage range
Switch
Weight
Dimensions
Output connector (power module)
Cable
Audio-Technica case style
Accessories furnished
BP892
In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry
professionals on request.
1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specications are subject to change without notice.
The donut-shaped moisture guard is provided to protect the element from
sweat and moisture. Position the moisture guard as close to the element as
possible to provide maximum protection. To remove the moisture guard, rst
remove the element cover and place it out of harm’s way. Gently slide the
moisture guard over the element. Replace the element cover.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Architect’s and Engineer’s Specications
The microphone shall be a xed-charge condenser designed for headworn
use. It shall have an omnidirectional polar pattern and a frequency response
of 20 Hz to 20,000 Hz. The microphone shall operate from an external 11V
to 52V DC phantom power source. It shall be capable of handling sound
input levels up to 135 dB with a dynamic range of 104 dB. Nominal open-
circuit output voltage shall be 3.5 mV at 1V, 1 Pascal. Output shall be low
impedance balanced (250 ohms). The microphone shall be RoHS compliant.
The microphone shall have a 1.4 m (55") permanently attached miniature
cable terminating in a locking 4-pin output connector. The output connector
shall connect to a jack on the included power module. The output connector
shall also connect to any Audio-Technica UniPak
®
body-pack wireless
transmitter. The power module shall contain a recessed switch to permit
choice of at response or 80 Hz low-frequency roll-off. The output of the
power module shall be a 3-pin XLRM-type connector.
The microphone shall be an underear headworn design with a diameter of 2.6
mm (0.10"). Microphone, boom and earpiece weight shall be 2.6 grams (0.09
oz). The microphone shall include a power module, a cable clip, a dual-ear
mount, two windscreens, two element covers, a moisture guard, a belt clip
and a carrying case. Finish shall be low-reectance black [beige].
Wireless models of the microphone shall also be available, terminated for
use with Audio-Technica UniPak
®
body-pack transmitters and a variety of
other manufacturers’ wireless systems. The wireless models’ dimensions,
polar pattern and included accessories (excluding power module and belt
clip) shall be identical to those of the wired model. The microphone shall
also be available unterminated.
The Audio-Technica BP892 [BP892-TH] is specied.
The Audio-Technica BP892cW [BP892cW-TH]; BP892cL4 [BP892cL4-TH];
BP892cLM3 [BP892cLM3-TH]; BP892cT4 [BP892cT4-TH]; BP892cT5
[BP892cT5-TH] (wireless version) is specied.
The Audio-Technica BP892c [BP892c-TH] (unterminated) is specied.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0162-01
Function Wire Color
Pin 1 Ground/Shield Green
Pin 2 Instrument Jumper to Pin 1
Pin 3 Mic Audio Copper Color
Pin 4 Bias + In Red
Function Wire Color
Pin 1 Ground/Shield Green
Pin 2 Bias + In Red
Pin 3 Mic Audio Copper Color
Pin 4 Source Load Jumper to Pin 3
Function Wire Color
Pin 1 Ground/Shield Green
Pin 2 Bias + In Red
Pin 3 Mic Audio Copper Color
Pin 4 Source Load Jumper to Pin 1
Pin 5 Line In Open
Function Wire Color
Pin 1 N/C Open
Pin 2 N/C Open
Pin 3 Bias + In, Red
Mic Audio
Shell/Case Ground/Shield Green
Function Wire Color
Sleeve Ground/Shield Green
Ring Mic Audio Copper Color
Tip Bias + In Red
BP892, cW, cW-TH
cT4, cT4-TH cT5, cT5-TH
cL4, cL4-TH
cLM3, cLM3-TH
 previous