AudioSource IW Five Speaker User Manual


 
Hooking It All Up
The speaker terminals on the IW Five will accommodate up to 16-gauge wire, which should be used for
longer connections. For shorter distances, 18-gauge speaker wire will be adequate. Leave about two feet of
extra wire at the speaker end to make it easier to install and position the IW Five. Do not use staples, nails,
or other metal objects to secure the speaker wire. The resulting short-circuit could affect your system's
performance and damage components in your system, especially the amplifier. You will get the best sound
quality and least amount of hum by keeping the speaker wires away from other electrical wires and cables.
When connecting your IW Five loudspeakers, it is very important to retain the correct polarity. This
means that the wire attached to the +, red, positive, or hot terminal on one component must be attached to
the +, red, positive, or hot terminal on the other component. Similarly, the , black, negative or ground terminals
must connect to the respective , black, negative or ground terminals. This is easy to do by observing the
color, stripe, or ribbing that appears on the wire. The amplifier terminals will also be marked left or right,
and should be connected accordingly.
Speaker Mounting
The IW Five loudspeakers are designed to be mounted directly into the ceiling or wall. Yes, you will be
cutting a hole in the ceiling or wall. With the right tools and a little extra care, installing the IW Five can be
both quick and easy. Use the enclosed template to accurately cut the mounting hole in the ceiling or wall.
Position the paper template where you have chosen to mount the speakers, and trace along the edge of the
circle. Make your cuts along this line. A utility knife will make the cleanest cuts in drywall. A keyhole saw
or electric jigsaw may also be used. Keep the cuts neat, although the frame will overlap the hole to hide any
rough edges. At this point, with the wall open, run the speaker wires into position, leaving about two feet
of extra wire at the opening. Observing proper polarity, connect the speaker wire to the terminals on the IW
Five. Remove the grille on the speaker, so you can reach the quick-turn mounting screws. Insert the speaker
into the mounting hole. Use a phillips head screwdriver to turn the screw slowly clockwise. The quick-turn
mounting system and frame will clamp around the wall to hold the speaker in place. Do not overtighten. If
you are unsure, consult a professional contractor. If you plan to paint the grille, do so before attaching them
to the speakers. The grille is held in place by a friction fit.
Enjoy your purchase.This manual provides detailed diagrams and instructions for setting up your
equipment.Our commitment to your satisfaction doesn't end there.We also offer friendly,toll-free assistance.
1-800-HELP-115
© 1998 AudioSource, Inc.
IW Five Specifications
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Hz to 20 kHz
Power Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 watts
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ohms
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB
Woofer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.25” polypropylene/graphite
Tweeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/8” polycarbonate dome
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8” diameter x 3” depth
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 lbs.
9300 North Decatur
Portland, OR 97203
Tel. 503.286.9300
Fax 503.978.3302