Filter
Top Products
AMP Series Products….. Value Priced Engineering Excellence!
Powerful, Flexible, Reliable.
All You Need to Bring Complete Satisfaction to Your Customer.
Flexibility by Design!
Power
Signal / Clip
Left
Signal / Clip
Right
Left
Right
-12dB
+6dB
Balance Trim
Volume Trim
Speakers
A B
AMP210
Stereo Power Amplifier
1. Power
The front panel power switch switches the AMP210/310 on or off.
2. Speaker Zone Selector
Selects active speaker output ( A or B )
3. Balance Trim
Fades speaker output between the Right and Left Channels
4. Volume Trim
Allows fine adjustment of amplifier volume.
FRONT PANEL CONTROLS
6. Line 1 Input
A switching input that can be used if a second source is desired. Will
take over when a signal is present. When there is no signal at this
input the amplifier switches back to the Line 2 or “primary” input.
7. Speaker Level Input Line Select
Switches the input of the speaker level input to Line 1 or Line 2.
8. Speaker Level Input
Can be used to connect a source with speaker level output instead of line
level outputs.
9. Line 2 Input/Output
The primary line level input and output for a single source connection.
10. Delay Time
Allows for a 3-15 second delay to be set and accommodate the source
connected to the Line 1 input.
11. Master Level Controls
Provides independent adjustment of Left and Right channel maximum
level.
12. Mode Select Switch
Switches the amplifier from Stereo mode to Bridged Mono mode
13. 12V Trigger
Allows the amplifier to be powered on by other electronics or to power
on other electronics via a 3.5mm mini phone plug cable.
14. Power Mode
Set it to Normal for manual power on/off. Set to Auto-On for signal sensing.
Set to Trigger when using 12V trigger for on/off.
15. Right Channel Speaker Output
Right channel terminals for speaker outputs A and B.
16. Left Channel Speaker Output
Left channel terminals for speaker outputs A and B.
17. Mains Power Inlet & Fuse Holder
Accepts IEC type line cord. A fuse located in integrated holder provides
safety protection from fault conditions: replace fuse with one of same type
and rating only.
18. Mains Voltage Selector
Voltage selection switch is preset to 115V (USA). For use in areas which
require 230V contact your dealer. Fuse must be of type and rating marked
on amplifier for use at local mains voltage.
REAR PANEL CONTROLS
4
3
2
1
6
7
8
9 10 11 12 13 14
15 16
17
18
5
5
5. Clip LEDs
Blinks red during signal clipping. Reduce volume slightly.
-
IN
L
L
R
L
R
R
Speaker IN
IN OUT
Line 1 Line 2
Line 1 Line 2
+ +
- -
V
V
Serial Number:
IN
OUT
Delay
Time
3 Sec 15 Sec
Master Level
Min Max
Min Max
Mode
Stereo Bridged
12V
Trigger
+
Trigger Normal
Auto On
LR
Use Class 2 Wiring
Minimum Impedance:
8 ohm Bridged
4 ohm Stereo
AVIS: RISQUE DE CHOC ELECTRIQE
NE
PAS OUVRIR CE CARTER
RESE
RVE AU PERSONNEL AUTORISE
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
COVER. NO USER SE
RVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
WARNING
: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
COVER. NO USER SE
RVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
CAUTION AVIS
Speaker A
R L
R
L
-
-
-
+ +
+
-
-
+ +
Bridge
Speaker B
115V~ 60Hz 700W
FUSE:T6.3A
L 250V
FUSE:T3.15A
L 250V
230V~ 50Hz 700W
MODEL AMP210
Custom Manufactured in China
CAUTION: See User Manual Before
Replacing Fuse
On Off
Light Bar Display
19
19. Light Bar Display Control
Turns light bar display on front panel on or off. Does not control Signal/Clip
LEDs or power button light ring.