Filter
Top Products
PAGE
36
Community XLT / XLTE Series Owner’s Manual
11
TECHNICAL SPECIFICATIONS
(Note: Specifications subject to change without notice)
11.1 FULL-RANGE MODELS
Model: 42 43 46 47
System Type
2-Way Trapezoidal 2-Way Trapezoidal 3-Way Trapezoidal 2-Way Trapezoidal
Frequency Response
70 Hz - 18 kHz 50 Hz - 18 kHz 50 Hz - 18 kHz 50 Hz - 18 kHz
Sensitivity (1W / 1m SPL)
97 dB 98 dB 99 dB 101 dB
Max. Power (RMS / Program)
Passive Mode
Biamp Mode LF
HF
200 W / 500 W
200 W / 500 W
50 W / 125 W
200 W / 500 W
200 W / 500 W
50 W / 125 W
200 W / 500 W
200 W / 500 W
80 W / 200 W
400 W / 1000 W
400 W / 1000 W
50 W / 125 W
Impedance
Passive Mode
Biamp Mode: LF
HF
8 Ohms (min 5.6)
8 Ohms (min 5.6)
8 Ohms
8 Ohms (min 5.3)
8 Ohms (min 5.3)
8 Ohms
4 Ohms (min 5.1)
4 Ohms (min 5.1)
8 Ohms
4 Ohms (min 3.2)
4 Ohms (min 3.2)
8 Ohms
Nominal Coverage H x V
90° x 40°
1
90° x 40°
60° x 40°
1
80° x 40°
Crossover: Type
Frequency
12 dB/octave
2 kHz
12 dB/octave
2 kHz
12 dB/octave
500 Hz / 2.5 kHz
12 dB/octave
1.8 kHz
Passive/Biamp Switch
Yes Yes Yes Yes
HF Level Switch
+4 dB / Flat +4 dB / Flat +4 dB / Flat +4 dB / Flat
PowerSense™ DDP
2
With Front / Rear Indication
Yes Yes Yes Yes
Drivers HF
3
MF
LF
1" / 25 mm Titanium
N/A
12" / 305 mm
1" / 25 mm Titanium
N/A
15" / 381 mm
1" / 25 mm Titanium
6.5" / 165 mm Cone
15" / 381 mm
1" / 25 mm Titanium
N/A
2 x 15" / 381 mm
Input Connectors
Neutrik NL4MP (Passive / Biamp)
1/4” Jack (Passive Mode only)
(2) In parallel
(2) In parallel
(2) In parallel
(2) In parallel
(2) In parallel
(2) In parallel
(2) In parallel
(2) In parallel
XLT Enclosure Material
XLT
XLTE
N/A
13-ply Baltic birch
Oriented strand board
13-ply Baltic birch
Oriented strand board
13-ply Baltic birch
Oriented strand board
13-ply Baltic birch
Mounting Points
XLT(5/16-18 threaded inserts)
XLTE (3/8-16 rig points)
N/A
3 top, 3 bottom
Sides/top/bottom
3 top, 3 bottom
Sides/top/bottom
3 top, 3 bottom
Sides/top/bottom
3 top, 3 bottom
Stand / Pole Socket
1-3/8” / 35 mm
diameter
1-3/8” / 35 mm
diameter
Attachment points
for external socket
None
All-Steel Handles
One on end One on each side One on each side One on each side
XLT Corner Protectors
N/A Yes Yes Yes
XLTE Rubber Feet
Yes Yes Yes Yes
Enclosure Finishes
XLT
XLTE
N/A
Black Paint
Black Carpet
Black Paint
Black Carpet
Black Paint
Black Carpet
Black Paint
Grille Material
Finish
16 Gauge perf steel
Black paint
16 Gauge perf steel
Black paint
16 Gauge perf steel
Black paint
16 Gauge perf steel
Black paint
Dimensions
4
Height
Width (front)
Width (rear)
Depth
23.4" / 618 mm
14.6" / 371 mm
9.2" / 234 mm
14.75" / 375 mm
26.9" / 684 mm
20.3" / 515 mm
13.7" / 347 mm
18.2" / 463 mm
33.9" / 862 mm
20.3" / 515 mm
13.7" / 347 mm
18.2" / 463 mm
41.9" / 1065 mm
20.3" / 515 mm
13.7" / 347 mm
18.2" / 463 mm
Pitch between sides
22 degrees 22 degrees 22 degrees 22 degrees
Weight XLT
XLTE
N/A
53.5 lb. / 24.3 kg
68.5 lb. / 31.1 kg
68.5 lb. / 31.1 kg
86.5 lb. / 39.2 kg
85 lb. / 38.6 kg
102 lb. / 46.3 kg
95 lb. / 43.1 kg
1 Horn can be rotated 90 degrees to reverse horizontal and vertical coverage pattern.
2
DDP = Dynamic Driver Protection.
3
Driver has as 2” diameter diaphragm and 1” exit.
4
Dimensions are for XLT models including corners. XLTE dimensions will vary up to approximately +/- 0.5 in. (+/- 13 mm)
from those listed. Model 42 is correct because it is only available as part of the XLTE Series.