Filter
Top Products
7
Instruction Manual
Front Panel Controls
The IWCB speakers have three
controls that help optimize
the speaker’s performance
regardless of mounting loca
-
tion or room acoustics.
HF (High Frequency) Level Control
This control adjusts the relative level of high frequency
output to compensate for varying room acoustics or
placement behind a screen.
“+” is for absorptive, acoustically “dead” rooms (or when
the speaker is behind a movie screen). Use this position
to increase the HF level and restore the proper sparkle and liveliness to
the sound.
“0” is for rooms of average absorptive characteristics.
“-“ should be used in rooms that are highly reflective, with hard floors
and exposed windows.
The setting of the HF control is mostly a matter of personal taste, so try it
in all three positions and see which one is preferred.
Boundary Compensation Control
Large room boundaries, such as floors, walls, and ceil-
ings, reinforce sound by acting essentially as acoustic
“mirrors.” When the speaker is mounted too close to the
corner or a wall/ceiling intersection, this sonic “reinforce
-
ment” often results in an unnatural heaviness or color
-
ation of the sound.
If it’s necessary to mount the speaker closer than 12 inches to the ceiling or
corner, you may find that by switching the Boundary Compensation control
“on,” the speaker sounds better. We recommend that you try the control in
both positions and see if it helps in your particular installation.
Directional Vector Control™
Oftentimes, it is visually advantageous to mount the
speaker high up on the wall, as this puts the speaker
above the field of vision and thus prevents any intrusion
by the speaker into the room’s décor.
However, acoustically, the best location for a speaker is at
seated ear level, about 3-4 feet off the floor.
The DVC electronically directs the midrange sound at the listener’s ears,
even when the speaker is mounted high up on the wall.
The “on” position directs the sound down at the listeners when using the
speakers as LCR theater speakers or primary stereo music speakers.
The “off” position fires the sound straight out from the speakers—above
the listener’s heads—which is perfect for non-localizable surround use, or
for room-filling background music (“whole house audio”) use.
IR Knockout
There’s an IR “knockout” plug in the upper right corner
of the front baffle. If you are using a multi-room con
-
trol system, you can install a standard IR receiver in the
knockout hole.
Should you have any questions or problems please feel free to contact us at
781-762-6300 or through our web site, www.atlantictechnology.com.
Specifications
IWCB-52 IWCB-525 IWCB-626
Type 2-way 2-way M-T-P array 2-way M-T-P array
Drivers Woofer 5 ¼” (135mm) GLH* 5 ¼” (135mm) GLH* 6 ½” (165mm) GLH*
Pressure Driver 5 ¼” (135mm) GLH* 6 ½” (165mm) GLH*
Tweeter 1" (25mm) soft dome 1" (25mm) soft dome 1" (25mm) soft dome
Frequency Response 75Hz – 20kHz ±3dB 64Hz – 20kHz ±3dB 54Hz – 20kHz ±3dB
Nominal Impedance 6 Ohms 6 Ohms 6 Ohms
Crossover Frequency 2.75kHz, 3rd order 2.5kHz, 3rd order 2.2kHz, 3rd order
Sensitivity 87dB 87dB 87dB
Recommended Power 10 – 120 Watts RMS 10 – 140 Watts RMS 10 – 140 Watts RMS
Dimensions 9
5
⁄16 x 17
11
⁄16 x 3
7
⁄8" 10
13
⁄16 x 19 x 3
7
⁄8" 12
5
⁄16 x 21
5
⁄8 x 3
7
⁄8"
(W x H x D) 236 x 449 x 100mm 274 x 484 x 100mm 312 x 547 x 100mm
Cutout Dimensions 8
1
⁄8 x 16 ½” 9
5
⁄8 x 17
7
⁄8” 11
1
⁄8 x 20
3
⁄8”
(W x H x D) 206 x 411mm 244 x 454mm 283 x 518mm
Net Weight 9lbs; 4.1kg each 10lbs; 4.6kg each 12lbs; 5.6kg each
*Graphite Loaded Homopolymer
Specifications are those in effect at the time of printing. Atlantic Technology reserves the right to change speci-
fications or appearance at any time without notice.
Dolby Digital, 5.1, Dolby Stereo and Dolby Pro Logic are trademarks of Dolby Laboratories Licensing Corpora
-
tion. DTS is a registered trademark of DTS Technology.
Front Panel Controls