Filter
Top Products
ifications
Arch itect's
Specif
ication
Ashly Model l5O0M
The
power
amplifier. being oftwo
channels, shall deliver a
minimum
power
oI 175 watts
per
channel into 8 ohm
loads or 275 watts
per
channel into 4 ohm loads with both
channels operating. When switched into bridged mono
node. it shall deliver at least 550 watts into m 8 ohm
load. The amplifier
shall be
immune
to damage from
shorted. open, or mismatched
loads.
The amplifier shall
have a
gain
of 29dB t .5dB
per
channel and
an
input
sen-
sitiviqr of 1.3 Volts ! 20/o lor lull rated output.
Frequency
response shall be 10Hz Io 2OkHz t .5d8. It shall be
stable
into any load including
pure
capacitors and inductors.
Hum and noise shall be at least 110d8
below full output
and SMPTE intermodulation distoftion shall be less
than
.010/o at full output. The
amplifier shall have rear
panel
switching for mono and bridging modes and rear mounted
level controls. The inputs shall be balanced bridging type
with male and female XLR type connectors as well as 1/4"
phone
jacks.
A three-color LED type indicator shall be
employed to show
the
power
level
of each chamel and self
contained
forced
air cooling shall be used. The
power
out-
put
devlces
shall be of the Lateral MOS FET
fpe.
The
anplifier shall lveigh 371b. net and mount in a
standard
19 inch rack using two spaces
(3.5"
high). The
power
requirement shall be 1 10 125VAC.
50 60H2.
The
porver
amplitier shall be an Ashly
FET- 1500M.
Ashly Model 1500C
'Ile
power
amplilier, being of two channels,
shall deliver a
minimum
power
ol 175 watts
per
channel into 8 ohm
loads or 275 watis
per
channel into 4 ohn loads wiLh
both
channcls operating. When switched into
bridged mono
mode. it shall deliver al leasi
550
watts
into an 8 ohm
load. The amplifier
shnll be imntune to dam:rge liom
shoried, open. or nisnratched loads. The amplifier shall
have a
gain
oi29dB t .SdB
per
ch:rnnel and an input sen-
sitivily of 1.3 Volts t 20/o lor ltll rated output. F-requency
response shall be 1OLIz to 2OkHz, t .5dts. It shall be stable
inlo irny
lo:rd
inclllding
pure
capacitors and inductors.
IIum :rnd noise shall bc at lcast I 1Odts below llll
output
ancl SMPI'E intermodulation clistortion shall be less
than
.010/o at Iull output. Thc amplilier shall have rear
panel
swikrhing lbr rrono and bridgine modes and rear
ntounted
level controls. The inputs
shall utilize 1/4'
phonc.jacks
as
well as terminal/barricr input strips.
Sell conLait.red lbrced
air cooling shall be used.
'l'he
porver
output dcvices shall
be ol the
Lateral
MOS-FET type. The nmplilier shall weigh
371b.
net
and
mouni
in a stanclard l9 inch rack usinq two
spaces
(3.5'
high), The
power
requirement shall be 110-
l2SVAC.
50-60H2.
The
power
amplilier shall
be
an Ashly FET-
I 500C.
Ashly Audio Inc.
100 Fernwood
Avenue
Rochester, New York 14621
Toll Free
(800)
828-6308
In NYS
(716)
544-5191
Since
1972
O
1989
Ashly Audio
ln
Canada:
Gerraudio Dist
363
Adelaide
Street East
Toronto,
MsA 1N3
(416)
361-1667
^'