Filter
Top Products
Quick Start Guide
UDM-RX01
Endeleo Multi-Format Receiver
Overview
Installed at the display device, the UDM-RX01 (FG-UDM-RX01) converts the signal
received from a UDM Multi-Format Distribution Hub to standard A/V signals (FIG. 1).
With intelligent receiver technology, each UDM-RX01 is powered directly from the
UDM Multi-Format Distribution Hub. As the hub is switched from one video/audio
source to another, the receiver detects a change in signal and automatically switches
the output device to its new video format.
Compatibility
The UDM-RX01 is compatible for use with the following UDM Hubs:
• UDM-0102 (FG-UDM-0102)
• UDM-0404 (FG-UDM-0404)
• UDM-1604 (FG-UDM-1604C)
• UDM-1604 (FG-UDM-1604)
Product Specifications
Configuration
The UDM-RX01 is configured via the UDM Hub’s WebConsole. Refer to the UDM
Hub’s Operation/Reference Guide for details.
Rear Panel Components
All of the connectors and ports are located on the rear panel (FIG. 2):
UDM Hub Port (RJ45)
The UDM-RX01 connects to the network through a connection to a UDM Hub. Refer to
the UDM Hub’s Operation/Reference Guide for details.
Serial Port
The Serial port is available for diagnostic and troubleshooting purposes.
The Serial port on the UDM-RX01 is an RJ12 connector, and requires a DB9-to-RJ12
adapter cable (FG-RS01) to connect to a PC for Terminal control.
IR Receiver (IR Rx) Port
The IR Rx port is used to enable user control and the remote compensation of the
video link to the UDM, using the FG-UDM-RC10 and the FG-IR03.
Refer to the Protocols and IR Learning section of the UDM Hub’s Operation/Reference
Guide for details for information on learning a device’s IR commands.
IR Transmit (IR Tx) Port
The IR Tx port issues IR commands from the UDM-RX01 to a controlled device. One
IR device (such as DVD player or VCR) can be connected to the UDM-RX01 via the IR
Tx port, and controlled via the UDM Hub’s WebConsole or via remote control.
Note: IR devices controlled via the IRTX ports are typically installed within the same
equipment rack as the UDM Hub and Receiver.
Connecting an IR Device to the IR Tx Port
1. Connect an IR01 Endeleo IR Emitter Module (FG-IR01) to the IR Tx port on the
UDM-RX01.
Note: Ensure the position of the device corresponds to the position assigned in
the Devices option of the UDM- Hub’s WebConsole.
2. Run the other end of the IR Emitter cable to the device’s IR sensor, and attach
the IR Emitter to the device’s sensor by removing the cover on the reverse side
of the IR Emitter.
IR commands for each device on the system have to be learned by the UDM hub in
order to function properly. Refer to the Protocols and IR Learning section of the UDM
Hub’s Operation/Reference Guide for information on learning a device’s IR
commands.
Audio Connectors
The UDM-RX01 provides standard Audio RCA output connectors for S/PDIF for digital
audio, and LEFT/RIGHT for analog audio output (FIG. 2).
Video Connectors
VGA Input at Display Device
1. Attach one end of the Endeleo VGA to VGA cable to the VGA connector on the
UDM-RX01.
2. Run the other end to the VGA connector on the display device. Connect firmly.
3. If appropriate connect audio to the audio connectors on the UDM-RX01.
Note: Ensure Input A is configured as a “VGA Input” and named appropriately
within the “Inputs” section of the Hub’s Configuration software. Also ensure the
correct Audio Type (Analog L/R or S/PDIF) is selected for the relevant input.
FIG. 1
UDM-RX01
UDM-RX01 Specifications
Power Requirements: 24VDC @ .75A
Note: The UDM-RX01 is remotely powered by the UDM
Multi-Format Distribution Hub (see
System Overview ).
Rear Panel Connectors:
Power Socket: 2.1mm barrel-style DC power socket (female)
UDM Hub (RJ45)
Port:
Provides audio/video transport as well as control via Cat5,
Cat5e or Cat6 to an UDM Hub.
Serial (RJ12) port: Enables an administrator to control the various functions
to the UDM-RX01 from a command line prompt and termi-
nal connection.
• Requires a DB9-to-RJ12 adapter cable (FG-RS01) to
connect to a PC.
• 9600, 8 bit, No Parity, 1 Stop Bit
IR Rx Port: 3.5mm stereo input port, for connection of an IR receiver
to allow setup of the UDM-RX01, local compensation
controls, and remote control of centrally located IR
devices.
IR Tx Port: 3.5mm stereo IR Transmitter output port allows one IR-
controlled device (such as a DVD or VCR player) to be
controlled via optional wired IR emitter.
Audio Connectors: • Black RCA female connector - Digital audio
• White RCA female connector - Analog audio Left
• Red RCA female connector - Analog audio Right
Video Connectors: • Yellow RCA female connector - CVBS (supports
composite video)
• S-Video - S-video female connector
• VGA - HD15 female connector (supports VGA video)
• Green RCA female connector - Component output: Y
• Blue RCA female connector - Component output: Pb
• Red RCA female connector - Component output: Pr
Operating Environment: • 35°F - 95°F (5°C - 35°C)
• Max. relative humidity - 85% (non-condensing)
Dimensions (HWD):
1" x 8 15/16” x 3 3/8” (25 mm x 227 mm x 85 mm)
Weight:
1.45 lb. (658 g)
Certifications: • CE
• FCC part 15 Class A
Other AMX Equipment: • RS232 DB9/RJ12 Connection Cable (FG-RS01)
• UDM-RC02 Multi-Format IR Remote Control
(FG-UDM-RC02)
• IR01 IR Emitter Module (FG-IR01)
• IR03 External IR Receiver Module (FG-IR03)
• UDM-PS 24VDC, 750mA Power Supply (FG-UDM-PS)
FIG. 2 UDM-RX01 - rear panel components
Serial port (RJ12)
IR Rx port
SPDIF female Digital Audio port
RCA audio
CVBS port
S-Video port
IR Tx port
VGA (HD15) port
Composite (Y) port
Composite (Pb) port
Composite (Pr) port
UDM HUB port (RJ45) - from an
“OUTPUT” port on the UDM Hub