Technicolor - Thomson RP2380 CD Player User Manual


 
Prog/Display SmartResume
When you stop CD play or power off the
unit (without disconnecting power sup-
ply), SmartResume is automatically activat-
ed. It stores all the current settings and
modes: current track, Shuffle, time display,
Mode (Repeat/Repeat All/Program), and
ESPX. When play mode is on again, the
unit RESUMES to the settings (unchanged)
and plays from the beginning of the track.
If CD compartment lid is opened, then
SmartResume stores only the following
modes: Shuffle Mode (Repeat/Repeat All),
and ESPX. Other settings such as track
play, time display, program setting and
memory are all reset or cancelled.
Repeating
You can replay the entire CD or one
track as many times as you wish as well
as listen to the beginning of each track for
10 seconds.
Press MODE successively to
1. Replay the entire CD .
2. Replay the current track
3. Replay the beginning of each track
for 10 seconds
(The number of the track being played will
be displayed and SCAN will appear.)
4. Press again to the function de-select
Program
This function lets you listen to the tracks
you selected in the order you want. The
CD player must be in Stop mode.
1. Press PROG. P will appear in the display.
2. Select the track to store by pressing
& press PROG again to
confirm.
3. Return to step 2 to store other tracks.
4. Press play button to listen to your
programming.
Note : The unit switches off automatically
after 15s if no key has been activated. To
prevent excessive battery consumption.
When programming, the unit can switch
off if you do not press any key within 10s.
If the unit switches off, the programme
will be stored in memory. Resume pro-
gramming as normal by turning the unit
on again.
You can program up to 24 tracks.
To play your program again, press play.
To add/edit tracks to the program, go to
stop mode ; press and hold PROG button
again. Refer to step 2 of the above para-
graph.
Listening to a Compact Disc
1. Slide the OPEN switch to the right
to open the door. Insert a disc and
press lightly on the centre to
lock. Close the door. Press PLAY/PAUSE
button. R
D
DDIISSCC
will appear in the
display. Then, the total
number of tracks and
time of the CD will be
displayed. If the
disc compartment
is empty or the
disc cannot be
played, NO DISC
will appear in
the display.
2. Shift CONTROL
switch to
“HOLD”
position to lock the
button to avoid
accidental activation of
unwanted functions.
You can also change tracks or quickly listen
to part of a track by pressing
down or holding
Listening to a CD in your car
(for RP2385 only)
1. Select a power source (either
battery power or the car DC adaptor)
2. Insert the cassette adaptor into the
tape deck and plug the cord into the
CD player’s PHONES jack of the unit.
3 . Insert a compact disc and press
PLAY/PAUSE button. Adjust CD
player’s volume to a mid level (make
sure the Bass Boost is turned off).
4. Use the car stereo to adjust
volume, tone ... Adjust the
volume of your CD
player for better
sound.
5. Before ejecting
the cassette when
you are finished,
make sure the car
stereo’s volume is
turned down.
The ELECTRONIC
SHOCK PROTECTION*
system prevents sound
interruptions when impacts
or vibrations occur. Electronic
anti-shock consumes less power and
increases the battery life. Therefore, the
ESPX function is always
ON.
After many successive
impacts, the buffer might
be emptied causing a
brief sound interruption for the memory
to reload. The buffer is 45 seconds long.
65
THE CD PLAYER
THE CD PLAYER
EN
DIGITAL SOUND
PROCESSING
TRACK MIN SEC
BASS BOOST
1
MHz
PRESET
P
SEEKFM
SURROUND
STEREO
25 PRESET
STATIONS
B
A
S
S
B
O
O
S
T
P
R
O
G
M
O
D
E
S
U
R
R
O
U
N
D
:
4
5
e
s
p
.
x
R
A
D
I
O
O
N
/
O
F
F
E
S
P
S
T
E
R
E
O
F
M
C
O
M
P
A
C
T
D
I
S
C
P
L
A
Y
E
R
45
EN
or
or
RP2380-990720 rev 1 6/21/01 3:15 PM Page 8