Filter
Top Products
38
masterpage:Leftfilename[\\Win-35\logitecmo\422958711MDSJE640CED\01GB03OPE-CED.fm]
Changing the recorded level after recording
Editing Recorded MDs
model name1[MDS-JE640] model name2[MDS-JE440]
[4-229-587-11(1)]
MDS-JE440
While monitoring the sound, turn AMS (or press
.
/
>
repeatedly) to change the recorded level
without turning on “OVER” on the peak level
meters.
5
Press AMS or YES.
“(S.F) Edit OK?” appears in the display.
6
Press AMS or YES.
The deck starts recording over the existing track.
“S.F Edit(:) ** %” appears while the track is being
recorded. An amount of time that is roughly equal to
or longer than the playback time of the track is
required when recording over the track. When the
recording finishes, “Complete!!” appears in the
display for a few seconds.
1
For MDS-JE640, press S.F EDIT.
“S.F Edit” appears in the display.
For MDS-JE440, do the following:
1
Press MENU/NO.
“Edit Menu” appears in the display.
2
Turn AMS (or press
.
/
>
repeatedly) until “S.F
Edit?” appears, then press AMS or YES.
2
Turn AMS (or press
.
/
>
repeatedly) until
“Fade In ?” or “Fade Out ?” appears, then press
AMS or YES.
3
Turn AMS (or press
.
/
>
repeatedly) until the
track number you want to change the recording
level appears, then press AMS or YES.
“Time 5.0s” appears in the display.
4
While monitoring the sound, turn AMS (or press
.
/
>
repeatedly) to change the Fade-in or
Fade-out Recording time.
The deck plays the portion that will be recorded over
using Fade-in or Fade-out Recording.
You can set the time at any value between 1 second
and 15 seconds, in 0.1 second increments. You cannot
set the time longer than the track.
5
Press AMS or YES.
“(S.F) Edit OK?” appears in the display.
6
Press AMS or YES.
The deck starts recording over the existing track.
“S.F Edit(:) ** %” appears while the track is being
recorded. When the recording finishes, “Complete!!”
appears in the display for a few seconds.
To cancel the operation
Press MENU/NO or
x
in steps 1 to 5. If you press AMS
or YES in step 6 and recording starts, you cannot interrupt
the operation.
z
(For MDS-JE640) You can use Edit Menu to perform
S.F Edit
1
While the deck is stopped, press MENU/NO.
“Edit Menu” appears in the display.
2
Turn AMS (or press
.
/
>
repeatedly) until “S.F Edit?”
appears, then press AMS or YES.
3
Turn AMS (or press
.
/
>
repeatedly) until “Tr Level ?,”
“Fade In ?,” or “Fade Out ?” appears, then press AMS or YES.
4
Turn AMS (or press
.
/
>
repeatedly) to adjust the
recording level or Fade-in or Fade-out Recording time.
5
Press AMS or YES.
Notes
•
Do not disconnect the AC power cord or move the deck
while recording is in progress. This may damage the
recording data preventing recording from being performed
properly.
•
You cannot change the recorded level of a track recorded in
LP2 or LP4 Stereo mode.
•
Do not use an MD that is damaged or dirty. This may prevent
recording data from being recorded properly.
•
Repeatedly changing the recording level results in poor sound
quality.
•
The recording level will not return to the exact original level
once the recording level has been changed even if it returned to
the original level.
•
The recording level cannot be changed while the timer is
activated.
Fade-in and Fade-out Recording
Avoid turning on these indicators