Filter
Top Products
How to use
English Stereo headphones
Features
Newly developed 50 mm driver unit for wide
response, and naturally powerful bass. OFC
voice coil allows for high input level (up to
3,000 mW).
Newly developed Advanced Direct Vibe
Structure
Provides an acoustically-tight seal for superior
sound isolation and deep bass. Optimized
diaphragm front chamber for more expansive
and clear mid-range sound.
Newly developed seamless earpad
Elasticized leather covered urethane pads with
seamless ear contact area for the ultimate in
wearing comfort and superior sound isolation
for deep bass.
Soft head cushion provides long-term listening
comfort.
Multiple-folding design for optimum
portability.
Newly developed, tangle-free serrated cord
Tiny serrations in the flat cord reduce tangling
caused by friction.
Using the Center button
Plays/pauses a track of the connected iPod
product with a single press. Skips to the next
track with a double press. Skips to the previous
track with a triple press. Starts the “VoiceOver*”
feature with a long press (if available).
Press once to answer the call. Press again to end.
Hold down for about two seconds to reject an
incoming call. When you let go, two low beeps
confirm the call was rejected.
* Availability of the “VoiceOver” feature depends
on iPod and its software version.
Note
Be careful not to unintentionally press any
buttons when you carry your iPod with this unit
connected.
Specifications
Type: Closed, dynamic / Driver unit: 50 mm,
dome type (OFC Voice Coil) /
Power handling
capacity: 3,000 mW (IEC*) / Impedance: 24 Ω at
1 kHz /
Sensitivity: 106 dB/mW / Frequency
response: 3 Hz – 29,000 Hz / Cord: 1.2 m
(47
1
/4 in), Litz cord(inline remote and microphone
cord for iPod/iPhone/iPad) /
Plug: Four-
conductor gold plated L-shaped stereo mini plug
(inline remote and microphone cord for iPod/
iPhone/iPad) /
Mass: Approx. 300 g (10.58 oz)
without cord /
Open circuit voltage level of the
microphone: –42 dB (0 dB = 1 V/Pa)
Supplied accessories
Inline remote and microphone cord for iPod/
iPhone/iPad (1) / Carrying case (1)
* IEC = International Electrotechnical
Commission
Design and specifications are subject to change
without notice.
Precautions
High volume may affect your
hearing. For traffic safety, do not use
while driving or cycling.
Because the headphones are of a high density
enclosure, forcing them against your ears may
result in eardrum damage. Avoid using the
headphones where they are liable to be struck
by people or other objects, such as a ball, etc.
Pressing the headphones against your ears may
produce a diaphragm click sound. This is not a
malfunction.
The supplied connecting cord is made
especially for the headphones. Other
connecting cords cannot be used with the
headphones.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
The validity of the CE marking is restricted to only
those countries where it is legally enforced,
mainly in the countries EEA (European Economic
Area).
Optional replacement earpads can be ordered
from your nearest authorized Sony retailer or
www.sony.com.
Compatible iPod/iPhone/iPad
models
You can use the unit with only the following
models supporting remote control. Update your
iPod, iPhone or iPad to the latest software before
use. In the Operating Instructions, iPod, iPhone
and iPad are collectively described as “iPod”
except in special cases.
iPod touch 4th generation
iPod touch 3rd generation
iPod touch 2nd generation
iPod nano 6th generation
iPod nano 5th generation (video camera)
iPod nano 4th generation (video)
iPod classic 120GB 160GB (2009)
iPod shuffle 4th generation
iPod shuffle 3rd generation
iPhone 4S
iPhone 4
iPhone 3GS
iPad (3rd Generation)
iPad 2
iPad
On copyright
iPhone
®
, iPod
®
, iPod classic
®
, iPod nano
®
,
iPod shuffle
®
, and iPod touch
®
are trademarks
of Apple Inc., registered in the U.S. and other
countries. iPad
®
is a trademark of Apple Inc.
“Made for iPod,” “Made for iPhone,” and “Made for
iPad” mean that an electronic accessory has been
designed to connect specifically to iPod, iPhone,
or iPad, respectively, and has been certified by
the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards.
Volume +*
Inline remote and microphone cord
Center button
Volume –
Microphone
* There is a tactile dot beside Volume +.
iPod/iPhone/iPad
Before putting the headphones in the supplied
carrying case, disconnect the cord. Otherwise the
cord may break.
Align small projections
with slots.
Tactile dot
MDR-X10
Stereo Headphones
Operating Instructions
Manual de instrucciones
4-430-815-12(1)
©2012 Sony Corporation Printed in China