Filter
Top Products
Sony Corporation 1980 Printed in Taiwan R. O. C
Operating Instructions
Mode d‘emploi
3-995-884-31(2)
FM/AM
2 Band Radio
ICF-9740W
Precautions
•Operate the set only on 120 V AC, 60 Hz.
•The nameplate indicating operating voltage, power consumption, etc. is
located on the rear exterior.
•Unplug the set from the wall outlet when it is not to be used for an
extended period of time. To disconnect the cord, pull it out by grasping
the plug. Never pull it by the cord.
•Do not install the set in a location near heat sources such as radiators or
airducts, or in a place subject to direct sunlight, excessive dust, mechanical
vibration, or shock.
•Allow adequate air circulation to prevent internal heat build-up. Do not
place the set on surfaces (rugs, blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.
•Should any liquid or solid object fall into the set, unplug the set and have
the set checked by qualified personnel before operating it any further.
•When the cabinet becomes soiled, clean it with a soft cloth dampened with
a mild detergent solution. Never use abrasive cleansers or chemical
solvents, as they may mar the cabinet.
•When an external antenna is used, disconnect it from the antenna
terminals of the set during a lightning storm, unless the installation
incorporates a suitable lightning arrestor.
If you have any question or problem concerning your set that is not covered
in this manual, please consult your nearest Sony dealer.
•Before operating the set, please read this manual thoroughly.
•This manual should be retained for future reference.
This instruction manual covers the USA and Canadian models of
the ICF-9740W table radio. Their performance and specifications
are identical except that the Canadian model has a recording jack.
WARNING
To prevent fire or shock hazard, do not
expose the set to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Specifications
Frequency range FM 87.5 - 108 MHz (3.42 - 2.78m)
AM 530 - 1,605 kHz (566 - 187 m)
Antennas FM: AC power cord antenna
External antenna terminals (75 ohms)
AM: Built-in ferrite bar antenna
Speaker Approx. 16 cm (6
3
⁄
8
inches) dia.
Power output 2W (at 10% harmonic distortion)
Power requirements 120 V AC, 60 Hz
Dimensions Approx. 330 x 232 x 136 mm (w/h/d)
(13 x 9
1
⁄
4
x 5
3
⁄
8
inches)
Incl. projecting parts and controls
Mass Approx. 2.2kg (4 lb 13 oz)
Design and specifications subject to change without notice.
FM EXT ANT
For the Customers in Canada
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
Location and Function of Controls
Perform the following steps in sequence for reception.
Dial Scale
FM External Antenna Terminals [FM EXT ANT] (rear)
See “Antennas”.
Recording Jack [†] (Canadian model only) (rear)
For recording radio programs with a tape recorder. Connect this
jack to the microphone input jack of your tape recorder with a
suitable cord. In the case of a Sony tape recorder, use the Sony
Connecting Cord RK-69A (optional).
The volume or tone control setting of the radio has no effect on the
recording.
Antennas
AM reception: The built-in ferrite bar antenna is used. Since the antenna is
directional, rotate the set horizontally for optimum reception, if necessary.
FM reception: Extend the attached AC Power Cord so that the FM
sensitivity will be increased, as it has the function of an FM antenna.
FM reception for difficult reception areas
In a steel-frame building, a mountainous area or at a long distance
from a transmitter, reception may be unsatisfactory. In that case,
connect a commercially available FM external antenna to the FM
EXT ANT terminals at the rear as illustrated.
4 TUNING Knob
Turn to select the frequency of the desired station, as
marked on the Dial Scale.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to
Article 820 - 40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as
practical.
feeder wire
or
coaxial cable
braid
center conductor
3 BAND SELECT Switch
Choose the desired band: FM or AM.
LOUDNESS Switch
Normally set the switch to OFF.
When listening to a program at a low volume, set the
switch to ON. This will compensate for our reduced
sensitivity to bass and treble at a low volume. The effect
of this control gradually decreases as the volume is
increased.
5 TONE Control
Turn towards HIGH for more treble, and towards
LOW for less treble.
2 Power/Volume Control [POWER/VOL]
Turn clockwise and the power will be on with a slight
click.
Turn it further for more volume.
After using, set it to OFF.
1 AC Power Cord
Connect to a wall outlet (120V AC).
English
Owner’s Record
The model number and the serial number are
located on the rear.
Record the serial number in the space provided
below. Refer to them whenever you call upon your
Sony dealer regarding this product.
Model No. ICF-9740W
Serial No.