Sony DRN-XM01HK2 Satellite Radio User Manual


 
Installation Guide
Sony Corporation ©2002 Printed in Japan
3-245-381-11(1)
OWNER’S RECORD
The model number is located on the bottom and serial number
also on the bottom. Record the serial number in the space
provide below. Refer to these numbers whenever you call upon
your Sony dealer regarding this product.
Model No.
Serial No.
DRN-XM01C2/DRN-XM01R2/
DRN-XM01H2/
DRN-XM01CK2/
DRN-XM01HK2
Digital Audio Receiver
Accessory Kit
Printed on 100%
recycled paper using
VOC (Volatile Organic
Compound)-free
vegetable oil based ink.
LIMITED WARRANTY
(Portable Audio)
For customers in the USA
Please register this product on line at
http://www.sony.com/
productregistration.
Proper registration will enable us to send you periodic mailings about
new products, services, and other important announcements.
Registering your product will also allow us to contact you in the
unlikely event that the product needs adjustment or modification.
Thank you.
For DRN-XM01H2/XM01HK2 Customers
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
INFORMATION
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
For All Models
Caution
•Do not operate the unit in a way that might divert your attention from
driving safely. As a driver, you alone are responsible for safely
operating your vehicle in accordance with traffic safety laws at all times.
•Do not install the unit where it may obstruct your view through the
windshield or your view of your vehicle’s indicator displays.
•Do not install the unit where it may hinder the function of safety
devices such as an air-bag. Doing so may prevent the air-bag from
functioning properly in the event of an accident.
•The installation and use suggestions contained in this manual are
subject to any restrictions or limitations that may be imposed by
applicable law— purchaser should check applicable law for any
restrictions or limitations before installing and/or operating this
product.
•Failure to follow these safety instructions and warnings may result in a
serious accident.
Parts for Installation and Connection
for DRN-XM01C2
for DRN-XM01R2
for DRN-XM01CK2
for DRN-XM01H2/XM01HK2
Car cradle (1)
Remote
commander (1)
Car stand (1)
Screw (5)
Cover (1)
Ferrite core (2)
Car battery
cord (1)
Car connecting
pack (1)
Car cradle (1)
Car stand (1)
Screw (5)
Remote commander (1)
RF modulator (1)
Cover (1)
Ferrite core (6)
Car cradle (1)
Car stand (1)
XM antenna (1)
Remote
commander (1)
Screw (5)
Cover (1)
Ferrite core (2)
Water proof
cushion (1)
Cable guide (3)
Cord clamp (4) Cushion with the
double-sided
adhesive tape (1)
Car battery cord (1) Car connecting pack (1)Seal (1)
XM antenna (1)
Remote
commander (1)
Ferrite core (2) Home cradle (1)
AC power adaptor (1)Audio cord (1)
Home stand (1)
For DRN-XM01C2/XM01CK2/XM01R2
Installing the Cradle in your
Car
Install the cradle with the supplied car stand.
1 Choose the mounting position, then shape the base of the
stand to match the mounting surface.
Note
Bend the base gently so there are no gaps between the base and the
mounting surface.
2 Clean the mounting surface well.
3 Peel off the protective film from the base of the stand and
attach the base to the mounting surface.
Make sure the base attaches to the mounting surface completely.
Notes
•The double-sided tape will not stick firmly if the mounting surface
temperature is lower than 20°C (68°F). Use a hairdryer, etc. to warm
up the mounting surface before mounting.
•Consider the mounting position carefully beforehand. If you change
the position after mounting the double-sided tape will weaken.
•When removing the stand, preheat the mounting surface with a
hairdryer then slowly pull up to remove, or use a commercially
available solvent to remove the seal.
4 Fix the stand with the supplied screws.
Note
Before drilling holes in the mounting surface, make sure there is
nothing behind the mounting surface.
5 Remove the knob.
6 Attach the supplied cover over the base of the stand as
shown below.
7 Attach the cradle to the stand.
1
2
3
To the stand receptacle
at the bottom of the
cradle
8 Adjust the angle.
You can also adjust the angle after installing the main unit into the
cradle.
Notes
•Do not install the unit in a location where it may be subjected to
extremely high or low temperatures as the cabinet may become
deformed or damaged. After parking your car, the temperature inside
the car may raise considerably. Therefore, cover the cradle and the main
unit with a white cloth or remove it from the cradle to avoid the direct
sunlight.
•Do not install the cradle, the main unit and RF modulator in the
following places:
– Underneath the driver’s seat: There may be a danger of the unit
getting lodged under the brake pedal.
– On the door or ceiling: There may be a danger of the unit falling down
or obscuring the driver’s view while driving.
For All Models
Affixing the ferrite cores
You must affix the cores (supplied with the model you purchased) in
order to comply with Part 15 of the FCC Rules.
Wind the cord around the ferrite core once or twice, and then fasten the
catch. Make sure that each ferrite core should be attached to the
appropriate position as shown in the diagram below.
Wind once or twice.
Cord
Fasten the catch.
Affixing the ferrite core to the RF modulator
POWER ANT
DC OUT AUDIO
RFC-8
RFC-8
RFC-8
RFC-8
RFC-8
Wind the cord around the RFC-8 ferrite
core once, then fasten the catch.
Approx.
10 mm
(13/32
inches)
Approx.
10 mm
(13/32
inches)
Wind the black
and red cords
around the RFC-
8 ferrite core
twice, then
fasten the catch.
Approx.
10 mm
(13/32
inches)
Wind the cord
around the
RFC-8 ferrite
core twice,
then fasten the
catch.
Wind the cord
around the RFC-8
ferrite core twice,
then fasten the
catch.
Approx. 5 mm
(7/32 inches)
Wind the cord around the RFC-
8 ferrite core once, then fasten
the catch.
Affixing the ferrite core to the XM antenna
Approx. 135 mm
(5 3/8 inches)
Affixing the ferrite core to the AC power
adaptor (AC-E60A)
Wind the cord around the
RFC-8 ferrite core twice,
then fasten the catch.
Approx. 5 mm
(7/32 inches)
Affixing the ferrite core to the car battery cord
(DCC-E260)
Wind the cord around the
RFC-8 ferrite core twice,
then fasten the catch.
Approx. 5 mm
(7/32 inches)
For DRN-XM01CK2
Installing the XM Antenna to
your Car
The bottom surface of the XM antenna is made of a magnet. Install the
antenna horizontally in a location where the radio wave from the satellite
is not interrupted by the body of the car (E.g., roof or trunk lid).
Notes on installing the antenna to your car
Place the antenna on a flat surface as far away as possible from the edges
of the trunk lid or the rear window.
•Before mounting the antenna, be sure to attach the supplied seal to the
body of the car where the antenna will be mounted, then mount the
antenna gently so that it does not damage the body of the car.
•Do not leave the cord slackened outside of the car.
•Use the cord clamp when fixing the cord, if required.
•When removing the antenna, do not pull it by the cord. This may cause
the cord to come off the antenna due to the powerful magnet.
•The antenna cord is charged with the XM signal and the power supply
to the antenna. When wiring the antenna, be careful not to pinch the
cord in the moving parts of the car. The damaged cable may cause a
malfunction of the antenna and the main unit.
•When washing the car in an automatic car wash, remove the antenna.
Otherwise, it may damage the body of the car.
Installing the antenna to an aluminum or plastic
body
The antenna cannot be installed on an aluminum or plastic body with the
magnet. In this case, use the supplied seal.
Painting the antenna
The antenna can be painted according to the body color of the car,
however, do not use paint that contains metal powder. This may cause
deterioration or inability of reception.
Do not disassemble the antenna when painting.
Placement of the car antenna
Place the antenna on a flat and even surface on your car roof. The angle
from the ground to the satellite should be about 20 - 60 degrees. If you
place the antenna on the trunk lid, make sure your car roof does not block
the satellite signal. Depending on where you live, you may be able to
receive radio waves that are retransmitted by ground repeaters.
Installing the Antenna on the Roof (recommended)
* Be sure to install the antenna firmly on a flat surface. Do not install
on the corner of the roof.
** Be sure to install the cord clamp in a lower position where the water
proof cushion is mounted. Otherwise, it will cause a water leak into
the trunk.
Clean the mounting surface before installing the cord clamp.
Leave the installed cord clamp for 24 hours before installing the
cord. Otherwise, the cord clamp may come off due to weak
attachment.
To install the cord, insert it into the cord clamp, then press the top
of the cord clamp downward so that the cord is securely installed
inside the cord clamp.
***• Cut the cable guide, if required.
It is difficult to attach the cable guide to a body or window which
has fluorine resin coating.
Figure of the top
Rubber packing
Inside of the trunk
Water proof cushion
Put the water proof cushion parallel on the rubber packing
using the double-sided adhesive tape.
Figure of the back
Water proof cushion
Rubber
packing
Cord
clamp**
Cord clamp**
Double-sided
adhesive tape
XM antenna*
Cable guide***
Cable guide***
Seal
Cord clamp**
Figure of the side
Rubber
packing
Cord clamp**
Water proof cushion
Put the water proof cushion on the rubber packing with the flat
surface downward using the double-sided adhesive tape.
Double-sided
adhesive tape
Leading the antenna cord into the car through
the space between the door and body
When installing the antenna on the roof, you can also lead the antenna
cord into the car through the space between door and body.
* •Clean the mounting surface before installing the cord clamp.
• Leave the installed cord clamp for 24 hours before installing the cord.
Otherwise, the cord clamp may come off due to weak attachment.
• To install the cord, insert it into the cord clamp, then press the top of
the cord clamp downward so that the cord is securely installed inside
the cord clamp.
Mounting the Antenna with the Supplied Seal and
Cushion with the Double-sided Adhesive Tape
Note
When removing the seal, preheat the mounting surface with a hairdryer
then pull up slowly to remove, or use a commercially available solvent to
remove the seal.
Installing the Antenna on the Trunk Lid
1 Mount the antenna on the trunk lid.
Clean the mounting surface before mounting.
2 Mount the water proof cushion on the right or left side of the
trunk lid.
To prevent rain water leakage inside the car along the cord, mount the
water proof cushion above the rubber packing when the trunk lid is closed.
* • Cut the cable guide, if required.
•It is difficult to attach the cable guide to a body or window which
has fluorine resin coating.
Cord clamp*
Cord clamp*
Antenna cord
Water proof cushion
Attach to the trunk lid.
1
3
Cushion with the
double-sided
adhesive tape
Seal
2
Attach to the antenna.
20° or less
Cable guide
Seal
Water proof
cushion
Rubber packing
Trunk lid
Cable guide*
Seal