Filter
Top Products
ST2432D Series
24” x 24” Hemispherically-Radiating
SpeakerTile
®
Recommended Installations:
•
9
/
16” T-bar suspended ceiling systems
•
15
/16
” T-bar suspended ceiling systems
Recommended Environment:
• Indoor or weather-protected outdoor
Recommended Accessories:
• PBB 2.0 Backbox kit
• ECS2432D Enclosure compensation module
• Safety Strap (secures SpeakerTile to back-
box)
HIGH QUALITY, WIDE-DISPERSION
INVISIBLE SPEAKERTILE
®
The Sound Advance
®
ST2432D SpeakerTile
®
is a remarkable combination of wide
bandwidth, wide dispersion, and a highly-refined aesthetic presentation, designed
for commercial installations. It is part of a unique family of truly invisible distributed
sound products from Sound Advance.
All ST2432D SpeakerTile models are available in several mounting options,
allowing them to be easily installed into standard T-bar suspended ceiling systems,
completely replacing a standard 2 ft x 2 ft ceiling tile.
The ST2432D is available in six different models, featuring a selection of standard
3-dimensional patterns or factory-applied surface finishes that allow a match with
almost any suspended ceiling tile pattern. The white Expanded PolyStyrene
®
(EPS)
front surface of the speaker tile allows all models to optionally be finished on-site
with any water-soluble finish, such as latex paint, or covered with light wallpaper,
fabrics and selected texture coats*, further enhancing the SpeakerTile’s ability to
blend invisibly with almost any interior design choice.
Patented Planar Diaphragm Technology™ allows a ST2432D that has been
properly installed in a suspended ceiling to radiate sound in a 140° hemispherical
pattern with smooth, even coverage. This dispersion characteristic allows ST2432D
speakers to be spaced farther apart than narrow-dispersion conventional speakers,
reducing the total quantity of loudspeakers required in almost any installation.
The ST2432D is a two-way, full-range device that utilizes a crossover centered at
1,200Hz, with 12dB per octave slopes for both low-pass and high-pass sections.
The ST2432D is transformer-coupled, with the following input taps: 0.5W, 1W, 2W,
4W, 8W, 16W, 32W and 8-ohm bypass.
An optional PBB 2.0 backbox is available, and is recommended for use when
the SpeakerTile is installed in air handling spaces. An optional ECS enclosure
compensation module is available, to optimize performance when the ST2432D is
used with the PBB 2.0.
[*Please contact Sound Advance for advice before applying any textured coating, light
wallpaper or fabrics to the ST2432D.]
T-Bar and
Ceiling Tile
Variations
Flush
15
/
16
” Grid
Tegular
15
/
16
” Grid
Tegular
9
/
16
” Grid
Tegular
9
/
16
” Grid
Flush
9
/
16
” Grid
Available Models:
ST2432D:
Plain white (shown in photo)
ST2432D-3D1:
Fine Fissured
®
(or similar) tile pattern
ST2432D-3D2:
Cortega
®
(or similar) tile pattern
ST2432D-3D4:
Fissured
®
(or similar) tile pattern
ST2432D-3D7:
Optima
®
/Ultima
®
(or similar) tile pattern
ST2432D-3D21:
Cirrus
®
(or similar) tile pattern
Tegular cuts are available to match tegular
ceiling tiles on
15
/16” T-bar grids. Tegular cuts
are not required to match tegular ceiling tiles
on
9
/16” T-bar grids. (See below for ceiling tile
examples.) Call Sound Advance for details.
Fine Fissured, Cortega, Fissured, Optima, Ultima and Cirrus are registered trademarks of Armstrong World Industries.