Filter
Top Products
1. INTRODUCTION
Model G6V
2. PROGRAM A VISOR REMOTE TO THE GTR SMART BUTTON
TM
4. REMOVE THE REMOTE CONTROL FROM THE SMART BUTTON
TM
Universal
Visor Transmitter
3. TROUBLE SHOOTING
Q: Door opener does not react after pressing the button on the transmitter?
A: - Ensure the button on the transmitter is pressed, the red light on the
transmitter comes on. Otherwise, check if the battery is inserted
properly.
- Ensure the wires that are previous connected to the wall mounted
door control are not loose.
- Ensure the remote control has been programmed to the Smart
Button
TM
. Refer to section 2 for how to program a transmitter to the
receiver.
You can delete the remote control(s) from the Smart Button
TM
,
first delete
all the remote controls, then learn the ones you would like to keep.
1. Press and hold the learn button for approx 10 seconds on the Smart
Button
TM
.
2. The LED will flash rapidly after 10 seconds to indicate all the pro-
grammed remote controls have been erased. You may now release
the learn button.
3. You have erased all the remote controls in the Smart Button
TM
.
Refer to the section in the Skylink
®
model GTR to install the Smart Button
TM
and follow the instructions below to program the transmitter.
1. With the GTR Smart Button
TM
connected on your
existing wall button. The red light on the Smart
Button
TM
should flash after plugging in the power.
If the red light on the Smart Button
TM
is flashing
slowly, that indicates it is in standby mode.
2. Press the learn button on the side of the GTR.
3. Once the learn button is pressed, the red LED
will flash quickly. You may release the learn
button.
4. Press the button on the transmitter you would
like to program.
5. Once the transmitter is programmed, the red
LED will flash slowly, in the same way as it
flashes in standby mode.
6. You can now operate the garage door opener
with this new remote control.
Learn Button
Universal
Visor Transmitter
(Battery included)
Congratulations on your purchase of the Skylink
®
Universal Visor Trans-
mitter Model G6V. The Model G6V works with the Skylink Smart Button
TM
.
In this package, you will find a visor remote with 12V battery.
7. WARNING
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
5. BATTERY
12 volt alkaline battery (size 23A)
included.
8. FCC
The Garage Door Remote Control is approved by the FCC and it complies with
Part 15 of the FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user’s authority to operate the equipment.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z487
US Patent. D377458
® are registered trademarks of their respective corporations
©2007 SKYLINK GROUP
9. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
10. CUSTOMER SERVICE
If you would like to order Skylink’s product or have difficulty getting your Skylink
remote control to work, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
You can add up to 15 additional transmitters to control the
same receiver. Skylink
®
offers Keychain Transmitters and
Keypad Transmitters to work with your receiver. For
more information, please visit our website at
www.skylinkhome.com or contact us.
6. ADDITIONAL TRANSMITTER
Visor clip