Samsung TS-H192C CD Player User Manual

Emergency eject hole
Disc compartment
Eject Button
If the compartment does not open
when you press the Eject button,
power off the computer, insert a pin
or unfolded paper clip in the hole
and push firmlhy)
Safety Precautions
The following are basic precautions to ensure user safety
and reduce the risk of property damage.
Sound output terminal
Interface terminal
Digital output
Master/slave select terminal Power terminal
EIDE cable, 4 screws.
Design and specifications are subject to change without prior notice.
Connecting the Cables
to the
Connecting the Cables
Connecting the power cable
The 4-pin power cable from the internal power unit of your computer must
be connected to the power terminal the rear of the CD-ROM drive.
Connecting the audio cable from a sound card
Connect the 4-pin audio cable between the sound output terminal on the
CD-ROM drive and the audio input terminal on the sound card.
Installing a jumper on the master/slave select terminal
Connect a jumper to the rear side of the CD-ROM.
If the jumper is connected to MA (Master), it will work in the Master mode.
If the jumper is connected to SL (Slave), it will work in the Slave mode.
If the jumper is connected to CS (CSEL), you can control the device by using the
host interface signal CSEL. (In general, connection to MA is recommended.)
Connecting the EIDE cable
Insert the EIDE cable (40-pin), which is connected to the hard
disk to the interface terminal.
(Place the red line of the cable close to the Pin 1.)
°ÿ Design and specifications are subject to change without prior notice.
Power cable
EIDE cable
Master/slave select terminal
Audio cable
CS : Cable Select(CSEL)
SL : Slave
MA: Master
When using one EIDE cable
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear
of the CD-ROM drive.
When using two EIDE cable
Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear
of the CD-ROM drive.
- If there is only one Optical drive: select MA (Master).
Hard Drive
Slave Drive (Choose the SL Jumper)
Hard Drive
Master Drive (Choose the MA Jumper)
-If there is two Optical drive, select MA (Master) / SL (Slave).
Hard Drive
Master Drive (Choose the MA Jumper)
Slave Drive (Choose the SL Jumper)
(Choose the MA Jumper)
(Choose the SL Jumper)
When you install the drive
While operating
Place the drive on a level
Do not place the drive in
direct sunlight.
Avoid low - or high-temperature
Avoid high-humidity environments.
Handle with caution to prevent
damage from external shock.
Do not drop the drive, and protect it
fromsevere shocks.
It can damage the drive or cause
it to malfunction.
Do not move the drive while in operation
and do not attempt to open the disc tray
byforce. Make sure to close all working
programs before attempting to open the tray
and always use the open/close button.
Do not use cracked, distorted or
damaged discs.
Do not insert a pin into the emergency
opening while in operation.
In particular, a disc with a crack on the
inner tracks may break while in use.
Never allow food particles or
foreign substances to enter the
drive casing.
To protect against the risk of
fire, do ot spill such liquids as
alcohol and benzene on the
Do not disassemble, attempt to repair or
modify the device without express
approval as directed in the manual.
To reduce the risk of damage,
electric shock, and fire.
Important to read and understand
at all times
Do not disassemble
1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole),
it is recommended that you make a copy immediately and use the copy instead. When a cracked disc is used continuously,
the size of the crack is likely to grow and it will eventually result in irreparable damage to the disc.
2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).
Any change or modification not expressly approved by designated qualified personnel could
void your authority to operate this device.
To warn the user that failure to comply with the instructions may result in
serious injury or death.
To caution the user that failure to comply with the instructions may result in
damage to property.
User's Guide - ENGLISH
FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Change or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate
the equipment.
IEC 60825-1 : 1993 + A1 : 1997 + A2 : 2001
BG68-01032A Rev.00
Installing the Drive
Installing the CD-Rom Drive
If necessary, attach a horizontal bracket
to both sides of the drive.
You can purchase these accessories separately
from your computer dealer.
(Screws for use: M3 X 6 X 4)
Remove the plate from a free expansion slot and install the
CD-ROM drive, as shown in the illustration.
If you have no free expansion slot, install the drive in place of the
diskette drive.
Make sure to use the standardized screws supplied (M3X6).
- To use screws other than M3X6 may result in malfunction.
System Requirements
Intel Pentium 166MHz(or higher), 16 MB of RAM (or higher) with an EIDE
98 / 2000 / ME / XP Windows NT 4.0 (or higher)
How to install the CD-ROM drive on your PC. First, remove the cover;
connect the cable to the CD-ROM drive and then to the PC.
Using the Drive/Storing and Cleaning
Your Discs
Push the power button and boot the computer.
After booting the computer, open the disc
compartment by pressing the Eject button.
Insert the disc (CD) with the label on the disc
facing upwards and close the disc compartment
by pressing the Eject button. The indicator light
comes on.
Play the disc (CD).
Using the CD-ROM Drive
Do not place a disc in direct sunlight.
Store a disc vertically in a well-ventilated and
stable location.
Do not write or attach a label on a disc.
Do not drop a disc or place heavy objects on it.
Do not touch the surface
of a disc; hold it by the
To clean a disc, polish lightly
from the inside of the disc to the
outside with a soft cotton cloth.
Storing Your Discs
Cleaning Your Discs
Run the CD player program supplied with the sound card or play the
Windows Media Player.
Playing CD-DA/Audio CDs
Follow the instructions provided with the disc.
A video card or MPEG software and a sound card need to be installed to view video CDs.
Playing Video CDs
The disc may not function properly if there are fingerprints, foreign substances or
dust on the disc surface.
If the drive is vertically installed, you cannot use an 8 cm MiniDisc because the disc is
Solving Technical Problems
The CD-ROM drive is not
detected by the computer.
After installing the CD-ROM
drive, the PC gets slower.
Check that the power, audio and EIDE cables are correctly
connected to the computer.
Change the EIDE cable and reconnect it to the computer.
Preferably, connect a second EIDE cable to the CD-ROM drive
in master mode.
Check the position of the jumper in the master/slave select
The CD-ROM drive is not
recognized by MS-DOS.
Reinstall the device driver or update it with the latest version by
downloading it from the Samsung Web site.
- http://
- http://
The CD-ROM drive is not
detected by Windows.
This case may occur when there is a Windows installation
problem; reinstall Windows.
No sound is heard from an
audio CD.
Check whether the audio cable is correctly connected to the sound
output terminal on the CD-ROM drive and the sound card CD-IN
Check that the sound card is operational.
When the MPEG software
plays a Video CD, the pictures
are not regular and the running
speed is too slow.
Adjust the size of the replay screen.
After checking the display resolution, adjust it, if necessary.
A CD is not read or is read
too slowly.
Check whether the CD is of good quality and clean it,
if necessary.
The disc compartment will
not open.
Check that the power cable is correctly connected.
Power off and disconnect the PC.
Insert a pin or unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
The CD-ROM drive is not
detected after it is connected
to a sound card.
The interface mode of the sound card is AT-BUS.
You must therefore connect the CD-ROM drive to the EIDE
port on the PC mother board, rather than to the sound card,
or install an EIDE compatible sound card.
The Disc is not in message is
displayed even though a disc
has been inserted.
The computer may not recognize the disc if you start playback
too quickly after inserting the disc.
Open and close the disc compartment and try again.
Clean the disc and try again.
The friction noise generated during SPIN-UP and STOP is caused by the
Automatic Ball Balancing System(ABS) and is not a malfunction.
Technical Specifications
Failure to do so may cause the
device to fall onto a hard surface,
resulting in damage or malfunction.
52X, 7800KB/s(MAX)
Disc types supported
Disc diameter
Data transfer rate
Access time (
Data buffer capacity
Slide mechanism
Spindle motor
Load mechanism
Eject button
Required power
Interface connector
Audio output
Jumper block
Storage area
Work area
Net weight
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,
Form-2, Photo-CD(Single, Multi-session), Video CD ready,
CD-Plus, CD-Extra, Enhanced CD, CD-I/FMV, CD-R/RW
120mm or 80mm
PIO Mode 4, DMA MW2, UDMA2
Semiconductor laser
Step Motor
Brushless motor
Tray, DC motor(Soft Eject)
Mode-1 : 1block / 10
bits, Mode-2 : 1 block/10
Auto eject or Auto inject
+5V DC 1.5A, +12V DC 1.5A
Line out 0.70 ± 20%(Vrms), 47kΩ
Molex 70203 or other compatible models
Temperature : 5~45 °C, Humidity : 10~80%
Temperature : -25~60 °C, Humidity : 10~90%
740g (set only)
125,000 POH (Duty 20%)
148.2 (W) x 42(H) x 184(D)mm