RCA PRO-LS200 Speaker User Manual


 
2
Do not place speakers where they
might be knocked over or exposed
to falling objects.
C
CC
Ce
ee
en
nn
nt
tt
te
ee
er
rr
r-
--
-C
CC
Ch
hh
ha
aa
ann
nnnn
nnel S
el Sel S
el Sp
pp
pe
ee
ea
aa
ake
keke
ker
rr
r
The center channel output contains the
majority of the dialogue and sound that
comes from on-screen action. Therefore,
you should place the center-channel
speaker as close as possible to the
television, either just above or below the
screen. Place the front edge of the center-
channel speaker grille flush with the edge
of the television.
N
NN
No
oo
ot
tt
te
ee
e:
: :
: The center-channel speaker is
magnetically shielded to prevent
interference with your television’s picture
when used on the supplied stand.
At
AtAt
Att
tt
ta
aa
ac
cc
ch
hh
hi
ii
in
nn
ng t
g tg t
g th
hh
he
e e
e S
SS
Sp
pp
peake
eakeeake
eaker
r r
r S
SS
St
tt
ta
aa
an
nn
nd
dd
d
Thread the supplied thumbscrew through
the hole in the bracket and into the screw
hole in the back of the speaker (make sure
the notches in the bracket face inward,
toward the speaker). Do not tighten it.
Adjust by rotating the stand until the
speaker is at the desired angle. Tighten
the thumbscrew securely (make sure the
notches on the stand lock into the
notches on the cabinet for a secure fit).
A
AA
At
tt
tt
tt
ta
aa
ac
cc
ch
hh
hi
ii
in
nn
ng
g g
g t
tt
th
hh
he
e e
e A
AA
An
nn
nt
tt
ti
ii
i-
--
-Sli
SliSli
Slip
p p
p P
PP
Pa
aa
ad
dd
ds
ss
s
The speaker is supplied with a set of four
anti-slip pads for the bottom of your
speaker. Push out each pre-cut circle from
the rubber square. Peel off the adhesive
backing. Then attach the pads to the
corners of the speaker.
C
CC
Co
oo
onn
nnnn
nne
ee
ec
cc
ct
tt
ti
ii
in
nn
ng
g g
g t
tt
th
hh
he S
e Se S
e Sp
pp
pe
ee
eak
akak
ake
ee
er
r r
r
t
tt
to
o o
o a
aa
an
n n
n A
AA
Am
mm
mp
pp
pl
ll
li
ii
if
ff
fi
ii
ie
ee
er
rr
r/
//
/R
RR
Re
ee
ec
cc
ce
ee
ei
ii
iv
vv
ve
ee
er
rr
r
C
CC
Ca
aa
au
uu
ut
tt
ti
ii
io
oo
on
nn
ns
ss
s:
::
:
Do not exceed the speaker’s
maximum power rating.
To avoid damage to the speaker or
amplifier/receiver, turn off the
amplifier/receiver before making the
connections.
Use 18-gauge speaker wire for
distances up to 50 feet. For greater
distances, use 16-gauge wire. Your
local RadioShack store has a wide
selection of speaker wire.
We recommend you use color-coded
or marked wire to help you correctly
connect the wire. Color-coded wires
have a stripe running down one side
of the conductors. Marked wires have
ridges along one side of the
conductors.
Bracket
Thumbscrew
Stand