Filter
Top Products
Getting started
01
7
En
English
Français
Deutsch
Nederlands
Italiano
Español
2 Place the microphone at your normal
listening position.
Place the mic about ear level at your normal
listening position using a table or chair.
Make sure there are no obstacles between the
speakers and the microphone.
3 If the receiver is off, press
STANDBY/ON to turn the power on.
4 Press MCACC SET UP.
Try to be as quiet as possible after pressing
MCACC SET UP
. The volume increases
automatically and the system outputs a series
of test tones.
If the noise level is too high,
Noisy!
blinks in
the display for five seconds. To exit and check
the noise levels
1
, press
MCACC SET UP
, or to
try again, press
ENTER
when
Retry?
shows in
the display.
The system now checks the microphone and
your speaker setup.
• If you see an
Err MIC!
or
Err SP!
message
in the display, there may be a problem with
your mic or the speaker connections. To try
again, press
ENTER
when you see
Retry?
2
When the MCACC setup is complete, the
volume level returns to normal and
Complete
3
shows in the display. The
MCACC
indicator
then lights to show that the MCACC setup is
complete and Acoustic Calibration EQ has
been activated.
4
Setting the clock
Setting the clock allows you to use the timer.
5
1 Press
TIMER/CLOCK
.
• If you are adjusting the clock, rather than
setting it for the first time, press
TIMER/
CLOCK
again.
2 If ‘Clk ADJ?’ isn’t in the display, select it
with
or
, then press
ENTER
.
3 Use
/
to set the hour. Press
ENTER
.
4 Use
/
to set the minute then press
ENTER
to confirm.
The display flashes to indicate the clock is set.
• Press
TIMER/CLOCK
anytime to display
the clock.
Using the on-screen displays
For ease of use, this system makes extensive
use of graphical on-screen displays (OSDs).
All the screens are navigated in basically the
same way, using the cursor buttons (
,
,
,
) to change the highlighted item and
pressing
ENTER
to select it.
6
Note
1• If the room environment is not optimal for the auto surround setup (too much ambient noise, echo off the walls, obstacles
blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air condition-
er, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.
• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV when doing the
auto surround setup.
2 If this doesn’t work, press
MCACC SET UP
, turn off the power, and check the problem indicated by the
Err
message, then try
the auto surround setup again.
3 If
Complete
doesn’t appear, it is likely an error occured during the setup. Please check all connections and try again.
4 See
Listening with Acoustic Calibration EQ
on page 13 for more on this.
5 If you unplug the system from the wall outlet, or there is a power outage, you will need to set the clock again.
6 The screen saver will appear after five minutes of inactivity.
DVD MENU
RETURN
MUTE
ST+
TUNE+
TUNE–
ST–
ENTERENTER
BASS
MODE
4 5
789
0
MAIN SUB
CLR
ENTER
SUB
9
6
TEST TONE CH LEVEL
DIMMER SR+
ADVANCED
SOUND
DIALOGUE
SURROUND
SETUP
SYSTEM
MIDNIGHT
QUIET/
CLOCK
TIMER/
XV-DV333-434.book 7 ページ ２００５年２月２３日 水曜日 午後１時５２分