Pioneer VSX-9110TXV-K Home Theater System User Manual


 
Controlling the rest of your system
11
66
En
The remote controls should be 1 to 2 inches apart.
5 Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver’s remote control.
For example, if you want to learn the playback control
signal, press and hold
briefly. The LCD display will
show
OK
if the operation has been learned.
1
If for some reasons the operation hasn’t been learned the
LCD will display
ERROR
briefly and then display
PRES
KEY
again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows
OK
.
2
Certain buttons represent operations that cannot be
learned from other remote controls.
3
The buttons
available are shown below (with the exception of the TV
controls, a combination of
SHIFT
and these buttons can
also be learned):
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold the RECEIVER button for a couple of
seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select
ERASE
then press
ENTER
.
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
3 Press the input source button corresponding to the
command to be erased then press
ENTER
.
The LCD display flashes
PRES KEY
.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows
OK
or
NO CODE
to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for a couple of
seconds when you’re done.
Resetting the remote control presets
This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select
RESET
then press
ENTER
.
RESET
flashes in the LCD display.
3 Press and hold
ENTER for about two seconds
.
The LCD shows
OK
to confirm the remote presets have
been erased.
Confirming preset codes
Use this feature to check which preset code is assigned
to an input source button.
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select READ ID then press
ENTER
.
The LCD on the remote prompts you for the input source
button you want to check.
Note
1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
2• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows
FULL
, it means the memory is full. See
Erasing one of the remote control button settings
below to erase a programmed button
you’re not using to free up more memory (note that some signals may take more memory than others).
3 Note that the number key decimal button (
+10
/
D.ACCESS
) may not be learned with some components.
1 to 2 inches
SLEEP
+
10
SR
+
ANALOG
ATT
DISC
VIDEO
SEL
DIMMER
CLASS
D.ACCESS
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TV CONTROL
SHIFT
VOL
DVD SAT
VIDEO 1TV CONT
DVR1
TUNE
TUNE
ST ST
STATUS
MCACCS.DIRECT
MULTI OPE
SIGNAL SEL
SBch
STEREO
MEMORY
TV CH
INPUT
SELECT
MPX
AUDIOSUBTITLE
ADV. SURR
STANDARD
ISOPHASE
THX
DTV INFO
MUTE
REC
TV VOL
i Pod
TUNER
RECEIVER
ENTER
REC STOP
HDD
CH
CH
DVD
AV PARA METER
TOP MENU ì
DTV MENU
CH LEVEL
MENU
T.EDI T
BAND
GUIDE
RETURN
SETUP
CATEGORY
CD
DVR2
CD-R
TV VIDEO 2
XM RADIO
ROOM2/3
DISP
RECEIVER
XM RADIO
ROOM 2HDMI2
CD-R/TAPE
DVR 2CD
ANALOG
AT T
MIDNIGHT/
LOUDNESS
VIDEO
SEL
DIMMER
SLEEP
SR+
+10
D.ACC ES S
DIALOG E
S.RETRIEVER
CLASS
DISC
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TUNE
TUNE
ST ST
ENTER
TOP MENU
AV P AR AM ETER CH LEVEL
CATEGORY
T.EDIT
DTV MENU
MENU
RETURN
GUIDE
BAND
SETUP
TV DVR1
TV CTRL
iPod
RECEIVER
TUNERHDMI1
DVD
TV CONTROL
SHIFT
VOL
STEREO
STATUS
SIGNAL SEL
THX
ADV.SURR
SBch
INPUT
SELECT
TV CH
MPX
AUDI O
DISP
SUBTITLE
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
RECDTV ON/OFF DTV INFO
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH
CH
DVD
RECEIVER
VSX-9110TXV_KU.book.fm 66 ページ 2006年4月4日 火曜日 午後5時15分