Filter
Top Products
Other Settings
12
92
En
Chapter 12:
Other Settings
The Input Setup menu
You only need to make settings in the Input Setup menu
if you didn’t hook up your digital equipment according to
the default settings (see Input function default and
possible settings on page 93). In this case, you need to
tell the receiver what equipment is hooked up to which
terminal so the buttons on the remote control
correspond to the components you’ve connected.
1 Switch on the receiver and your TV.
Use RECEIVER to switch on.
2 Set the operation selector switch to
RCV
, then press
HOME MENU
.
An on-screen display (OSD) appears on your TV. Use /
// and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
3 Select ‘
System Setup
’ from the
HOME MENU
.
4 Select ‘
Input Setup
’ from the
System Setup
menu.
5 Select the input function that you want to set up.
The default names correspond with the names next to the
terminals on the rear panel (such as DVD or VIDEO 1)
which, in turn, correspond with the names on the remote
control.
6 Select the input(s) to which you’ve connected your
component.
For example, if your DVD player only has an optical
output, you will need to change the DVD input function’s
Digital In setting from COAX-1 (default) to the optical
input you’ve connected it to.The numbering (OPT-1 to 4)
corresponds with the numbers beside the inputs on the
back of the receiver.
• If you change the setting to an input that has been
previously assigned to another function (for example,
TV/SAT), then the setting for that function will
automatically be switched off.
• If your component is connected via a component
video cable to an input terminal other than the
default, you must tell the receiver which input
terminal your component is connected to, or else you
may see the S-Video or composite video signals
instead of the component video signals.
1
7 When you’re finished, proceed to the settings for
other inputs.
There are three optional settings in addition to the
assignment of the input jacks:
• Input Name – You can choose to rename the input
function for easier identification. Select Rename to
do so, or Default to return to the system default.
• 12V Trigger 1/2 – After connecting a component to
one of the 12 volt triggers (see Switching components
on and off using the 12 volt trigger on page 70), select
MAIN, ZONE 2, ZONE 3 or OFF for the corresponding
trigger setting to switch it on automatically along
with the (main or sub) zone specified.
• PDP In (SR+) – To control certain functions on this
receiver from a flat panel TV, select the display input
to which you’ve connected the receiver.
2
8 When you’re finished, press
RETURN
.
You will return to the System Setup menu.
DVD
RECEIVER SOURCE
MAIN
MULTI
OPERATION
ZONE2 3
VIDEO1
GALLERY
HOME MEDIA
CD
HDMI XM
SIRIUSTUNER
PHONO
VIDEO2 VIDEO3
TV
BD DVR1 DVR2
CD-R
RECEIVER
SOURCE
TV RCV
VOL
VOL
TV CONTROL
CH
SOURCE
TV RCV
AUDIO
PARAMETER
TOP MENU
BAND
iPod CTRL
CATEGORY
EXIT
TOOL S
STATUS PHASE CTRL CH LEVEL
MENU
T.EDIT
VIDEO
PARAMETER
INPUT MUTE
TUNE
TUNE
ST ST
MUTE
RETURN
HOME
MENU
RETURN
ENTER
A/V RECEIVER
Exit Return
a.Manual SP Setup
b. Input Setup
c. OSD Language
d. Other Setup
4.SystemSetup 4b.Input Setup
A/V RECEIVER
Exit Finish
INPUT : DVD
Input Name : Default
Digital In : COAX-1
HDMI Input :
---
Component In : Comp-1
12V Trigger1 : OFF
12V Trigger2 : OFF
PDP In (SR+) : OFF
Note
1 For high-definition video (using component video connections), or when digital video conversion is switched off (in Setting the Video options
on page 98), you must connect your TV to this receiver using the same type of video cable as you used to connect your video component.
2 You will have to make an SR+ cable connection from a CONTROL OUT jack on the display to the CONTROL IN jack on this receiver (opposite
from the setup in Using this receiver with a Pioneer flat panel TV on page 70). Note that to control this receiver using the remote, you will have
to point it at the flat panel TV’s remote sensor after making this connection.
4b.Input Setup
A/V RECEIVER
Exit Finish
INPUT : DVD
Input Name : Default
Digital In : COAX-1
HDMI Input :
---
Component In : Comp-1
12V Trigger1 : OFF
12V Trigger2 : OFF
PDP In (SR+) : OFF
4b.Input Setup
A/V RECEIVER
Exit Finish
INPUT : DVD
Input Name : Rename
Digital In : COAX-1
HDMI Input :
---
Component In : Comp-1
12V Trigger1 : OFF
12V Trigger2 : OFF
PDP In (SR+) : OFF
SC07-05.book Page 92 Friday, April 25, 2008 11:59 AM