Filter
Top Products
11
<DRB1297>
En
DJ PLAYER OPERATION
Auto Cueing (*)
Auto cueing is used to automatically specify the Cue point (see p. 12) to be used
before sound actually begins to play when inserting a disc or when performing
track searching.
¶ Turning auto cueing on and off
Pressing the TIME MODE/AUTO CUE button and holding it down for a
second or more causes auto cueing to be alternately turned on and off.
When AUTO CUE is on, the [A. CUE] indicator will be lit up.
Starting Playback
1. Insert a disc in the player.
This unit spins discs at high speeds to provide high performance. As a result,
disc loading takes a couple of seconds.
2. If auto cueing is on, press the PLAY/PAUSE button (3/8).
¶ Wait for the CUE button indicator to light up before pressing the button.
The silent portion at the beginning of the displayed track will be skipped
and playback will begin instantaneously from the first bars of the track.
Once the first track has been played, the player will automatically search for
the beginning of the next track to be played. The cueing indicator [CUE] will
light up, the PLAY/PAUSE button [3/8] indicator will flash, and the player
will then wait for the PLAY/PAUSE button (3/8) to be pressed before begin-
ning playback of the next track.
Jog dial
DISC LOADING/UNLOADING
¶ Only one disc can be loaded at a time. Never attempt to load more than one
disc at the same time, or attempt to load a second disc when one disc has
already been loaded.
¶ When loading a disc, do not placing any twisting force on the disc, or try to
force the disc into the slot. Also, do not attempt to interrupt or defeat the
motion of the disc when the player begins to draw a disc into the slot or to
eject a disc, since damage to the disc or player could occur.
3. The disc can be ejected anytime using the EJECT button (0)
when the EJECT UNLOCK/LOCK switch is set to UNLOCK.
When the EJECT UNLOCK/LOCK switch is set to LOCK,
press the PLAY/PAUSE button (6) during playback, or
when a Cue point has been set, press the CUE button
(back cue) before pressing the EJECT button (0) to
eject the disc.
¶ When the EJECT button is pressed, disc rotation stops and the disc is ejected
from the loading slot.
¶ If the disc cannot be ejected with the EJECT button, insert a pin in the
forced ejection hole on the front panel of the player. ☞ P. 5
CAUTION:
Do not attempt to press a disc back into the slot when the [EJECT]
indicator appears. Pressing a disc back into the slot while the [EJECT]
indicator appears may cause the player to stop. In this case, press the
EJECT button again and wait until the [EJECT] indicator goes out be-
fore reinserting the disc.
Label surface up
Insert straight
1. Set the rear-panel POWER switch to ON.
2. Insert a disc.
¶ Hold the disc with label surface upwards, and insert into the front panel
disc loading slot .
¶ When playing 8cm discs, be sure to install an adaptor.
Do not force a disc into the unit when the POWER switch is set to OFF
as this may damage the disc and the unit.
This unit spins at high speed to provide high performance. When
playing 8cm discs with an adaptor, for safety reasons the rotation
speed is reduced as a result scratch and reverse speeds will be lower.
¶ AUTO CUE on/off status is stored in memory and persists even when the
power is turned off.
¶ It can change the Auto Cue level.
7 Changing the Auto Cue level
1. Press the TIME MODE/AUTO CUE button for over 5
seconds.
¶ The display will indicate [A.CUE-60dB] (in the original state).
2. By -pressing the WAVE SEARCH (ZOOM) button (2, 3)
you can change the level.
¶ It can choose from -36dB, -42dB, -48dB, -54dB, -60dB, -66dB, -72dB and
-78dB.
¶ The level change mode can be removed if you press the TIME MODE/
AUTO CUE button or wait 15 seconds.
¶ Even if you turn the power off, the set level will remain in memory.
Buttons indicated by * cannot be used when the Digital Mode
switch is set to on (and the digital output terminal is used).
BASIC OPERATION
TIME MODE
/ AUTO CUE
CUE
SEARCH
TRACK
SEARCH
PLAY/PAUSE
EJECT
EJECT UNLOCK/LOCK
1, ¡
4, ¢
6
0
WAVE SEARCH(ZOOM)
2, 3