NEC Headset Cordless Headphones User Manual


 
QUICK START GUIDE
H
EADSET
C
ORDLESS
II
DTERM
Pri
nted in China 63913-02 (01-05)
©
2003-2005 Plantronics, Inc. All rights reserved. Plantronics, the logo design,
and Plantronics and the logo design combined are trademarks or registered
tradema
rks of Plantronic, Inc. All other trademarks are the property of the
resp
ective owners.
Patent U.S. 5,210 791 ; 6,735,453; D492,667 and D496,029; EM 69109
IMPORTANT SAFETY INSTRUCTIONS
8. Do not overload outlets and extension cords as this
can result in risk of fire or electric shock.
9. Never disassemble or push objects of any kind into
the pr
oduct as this may short out parts which could
result in a fire or electric shock. Never spill liquid of
any kind on the product.
10. Use caution when installing or modifying telephone
lines.
11. This product is intended to be powered by a Listed
Class 2 Direct Plug-In Power Unit, rated at an input
voltage of 120 VAC, 60Hz and an output voltage of
9 VDC at 800mA.
12. This product requires AC power in order to operate.
In order to have phone service during a power
outage, have another telephone available that is
powered only by the telephone line.
13. Keep all product cords and cables away from
operating machinery.
14. Avoid using telephone equipment during an
electrical storm.
15. Do not use this equipment to report a gas leak in
the vicinity of a gas leak.
16. Never allow children to play with the headset.
When using your telephone equipment these
basic safety precautions should be followed to
reduce the risk of fire, electric shock, and injury
to persons.
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the
product. The symbol identifies and alerts the user
to the presence of important operating, safety, and
service instructions.
3. This product contains gold-plated nickel, phosphor
bronze and copper. If you experience a skin irritation,
discontinue use and contact Plantronics.
4. Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
5.
Do not locate this product near water, for example,
near a bathtub, or sink, in a wet basement, or near
a swimming pool.
6. This product should never be placed near or over a
radiator or heat register. It should not be placed in
a built-in installation unless proper ventilation is
provided.
7. Do not allow anything to rest on the power cord.
Do not locate this product where persons walking
on it will damage the cord.
To reduce the risk of fire or injury to persons, read
and follow these instructions.
1. Always insert batteries correctly with regard to polarity
(+ and -) marked on the battery and the equipment.
Incorrectly installed batteries can overheat, causing
leakage and or explosion.
2. Immediately r
emove discharged batteries from the
equipment to avoid leakage.
3. Remove batteries if the equipment is not used for an
extended period of time.
4. Do not heat, cr
ush, deform, or puncture batteries.
This can result in leakage and or explosion.
5. Do not disassemble the batteries. This can result in
contact with the har
mful components.
6. Do not dispose of batteries in a fire. This can result
in an explosion.
7. Do not char
ge batteries. Attempting to char
ge a non-
rechargeable battery can result in leakage, explosion
and or fir
e.
8. Keep batteries out of the reach of children.
SA
VE
THESE INSTRUCTIONS
BATTERY PRECAUTIONS
FCC REGISTRATION INFORMATION
FCC Requirements—Part 15
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.This device may not cause har
mful inter
ference, and
2.This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC R
ules. These limits are designed to provide reasonable
pr
otection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception which can
be deter
mined by tur
ning the radio or television off and on, the
user is encouraged to tr
y to cor
r
ect interference by one or more
of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician
for help.
RF Exposure Information
This device and it’s antenna must not be co-located or
operated in conjunction with any other antenna or transmitter.
To comply with FCC RF exposure requirements, only use
supplied antenna. Any unauthorized modification to the
antenna or device could void the user's authority to operate
this device.
FCC Requirements—Part 68
This equipment complies with P
art 68 of the FCC R
ules and
the requirements adopted by ACTA. On the bottom of the
base unit of this equipment is a label that contains, a pr
oduct
identifier in the for
mat US:A
A
AEQ##TXXXX. If r
equested,
this infor
mation must be pr
ovided to your telephone company
.
If this equipment causes harm to the telephone network, the
telephone company will notif
y you in advance that temporar
y
discontinuance of service may be required. But if advance
notice isn't practical, the telephone company will notif
y the
customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it
is necessary.
The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
pr
oper functioning of your equipment. If they do, you will
be notified in advance in or
der for you to make necessar
y
modifications to maintain uninterrupted service.
If trouble is experienced with this unit, for repair or warranty
information, please contact customer service at the address
and phone listed in the W
ar
ranty section of this User
’s Guide.
INDUSTRY CANADA NOTICE
Notice: This equipment meets the applicable Industry Canada
T
er
minal Equipment T
echnical Specifications. This is confirmed
by the r
egistration number. The abbreviation, IC, before the
registration number signifies that registration was performed
based on a Declaration of Confor
mity indicating that
Industry Canada technical specifications were met. It does
not imply that Industry Canada approved the equipment.
The Industr
y Canada r
egistration number is located in the
bottom of the unit. Before installing this equipment, users
should ensur
e that it is permissible to be connected to the
facilities of the local telecommunications company. The
equipment must also be installed using an acceptable
method of connection. The customer should be awar
e
that compliance with the above conditions may not prevent
degradation of ser
vice in some situations. Repairs to certified
equipment should be coor
dinated by a representative
designated by the supplier
. Any repairs or alterations made
by user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the
user disconnect the equipment. Users should ensure for their
own pr
otection that the electrical gr
ound connections of the
power utility, telephone lines and internal metallic water pipe
system, if pr
esent, ar
e connected together
. This precaution
may be particularly important in r
ural ar
eas.
Caution: Users should not attempt to make such connection
themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
RSS 210
This digital apparatus does not exceed the Class B limit
for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of Industry Canada.
Operation is subject to the following two conditions:
1) this device may not cause inter
fer
ence, and 2) this device
must accept any interference, including interference that
may cause undesir
ed operation of the device.