Filter
Top Products
16
M•26
00
: STEREO SYSTEM BIAMPED WITH BRIDGED SUBWOOFER
+
–
SERIAL NUMBER
MANUFACTURING DATE
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
2600 WATTS
4 OHM LOAD MIN.
120 VAC 60 Hz
2000 WATTS
STEREO
TYPICAL
CH
1
CH
2
+
––
+
MONO
BRIDGE
• THE FOLLOWING ARE REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "FR SERIES", AND THE "RUNNING MAN" FIGURE •
CONCEIVED AND DESIGNED BY MACKIE DESIGNS INC • WOODINVILLE
WA • 98072 • USA • PATENTS PENDING • COPYRIGHT ©1998
1300 WATTS / CH
2 OHM LOAD MIN.
1
CHANNEL
MONO
BRIDGE
S
U
B
W
O
O
F
E
R
TYPICAL
35 Hz
CHANNEL
2
ON
TYPICAL
CAUTION
LETHAL VOLTAGES MAY APPEAR AT OUTPUT
TERMINALS. CLASS 1 WIRING IS REQUIRED
SPEAKER OUTPUTS
IN
IN
LOW CUT FILTER
INPUT
INPUT
CROSSOVER
SWITCHED OUTPUT
SWITCHED OUTPUT
BALANCED
OR
UNBALANCED
170 Hz
100 Hz
OFF
STAGE
MONITOR
90Hz
LOW
OUT
HIGH
OUT
THRU
LOW
OUT
HIGH
OUT
THRU
120Hz
60Hz
CROSSOVER
90Hz
120Hz
60Hz
AMP MODE
BRIDGED
MONO
OUTPUT APPLICATION
BALANCED
OR
UNBALANCED
LIMITER
(CH1 & CH2)
LOW OUT
(SUB WOOFER)
OFF
CH's
SUMMED
FULL
RANGE
LOW CUT FILTER
170 Hz
100 Hz
OFF
STAGE
MONITOR
S
U
B
W
O
O
F
E
R
TYPICAL
35 Hz
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVI S:
RISQUE DE CHOC ELECTRIQUE
— NE P
AS OUVRIR
PIN 1+ CH1+
PIN 1
–
CH1
–
PIN 2+ & 2
–
NOT USED
PIN 1+ CH2+
PIN 1
–
CH2
–
PIN 2+ & 2
–
NOT USED
PIN 1+ BRIDGE +
PIN 1
–
BRIDGE
–
PIN 2+ & 2
–
NOT USED
THRU
THRU
SERIAL NUMBER
MANUFACTURING DATE
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
2600 WATTS
4 OHM LOAD MIN.
120 VAC 60 Hz
2000 WATTS
STEREO
TYPICAL
CH
1
CH
2
+
––
+
MONO
BRIDGE
• THE FOLLOWING ARE REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "FR SERIES", AND THE "RUNNING MAN" FIGURE •
CONCEIVED AND DESIGNED BY MACKIE DESIGNS INC • WOODINVILLE
WA • 98072 • USA • PATENTS PENDING • COPYRIGHT ©1998
1300 WATTS / CH
2 OHM LOAD MIN.
1
CHANNEL
MONO
BRIDGE
S
U
B
W
O
O
F
E
R
TYPICAL
35 Hz
CHANNEL
2
ON
TYPICAL
CAUTION
LETHAL VOLTAGES MAY APPEAR AT OUTPUT
TERMINALS. CLASS 1 WIRING IS REQUIRED
SPEAKER OUTPUTS
IN
IN
LOW CUT FILTER
INPUT
INPUT
CROSSOVER
SWITCHED OUTPUT
SWITCHED OUTPUT
BALANCED
OR
UNBALANCED
170 Hz
100 Hz
OFF
STAGE
MONITOR
90Hz
LOW
OUT
HIGH
OUT
THRU
LOW
OUT
H
IGH
OUT
THRU
120Hz
60Hz
CROSSOVER
90Hz
120Hz
60Hz
AMP MODE
BRIDGED
MONO
OUTPUT APPLICATION
BALANCED
OR
UNBALANCED
LIMITER
(CH1 & CH2)
LOW OUT
(SUB WOOFER)
OFF
CH's
SUMMED
FULL
RANGE
LOW CUT FILTER
170 Hz
100 Hz
OFF
STAGE
MONITOR
S
U
B
W
O
O
F
E
R
TYPICAL
35 Hz
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVI S:
RISQUE DE CHOC ELECTRIQUE
— NE P
AS OUVRIR
PIN 1+ CH1+
PIN 1
–
CH1
–
PIN 2+ & 2
–
NOT USED
PIN 1+ CH2+
PIN 1
–
CH2
–
PIN 2+ & 2
–
NOT USED
PIN 1+ BRIDGE +
PIN 1
–
BRIDGE
–
PIN 2+ & 2
–
NOT USED
THRU
THRU
STEREO
20Hz
20Hz
BRIDGED
CHOOSE
CHOOSE
CHOOSE
CHOOSE
LIMITER ON
HIGH
OUT
HIGH
OUT
LOW OUT
(SUBWOOFER)
FROM MIXING CONSOLE
MAIN RIGHT OUT
FROM MIXING CONSOLE
MAIN LEFT OUT
This amplifier receives the frequency
range above the first amplifier's
CROSSOVER point.
NOTE: Set the LOW CUT FILTER to
below the CROSSOVER point of the
first amplifier, or you will miss part of
the bass range.
Because the OUTPUT APPLICATION
switch is set to LOW OUT, this
amplifier plays the frequency range
below the CROSSOVER point (60, 90,
or 120Hz).
Set the LOW CUT FILTER to the
lowest frequency your subwoofers can
handle.
Set the THRU switch to HIGH OUT
so the second amplifier will receive the
frequency range above the
CROSSOVER point.
This example also illustrates the
BRIDGED MODE, playing a single
subwoofer. Both input signals are
summed in this mode, so the
subwoofer plays the combined
channel 1 and channel 2 signal.
The outputs going to the other
amplifier are not summed.
MAIN SPEAKERS
(play above 90Hz
in this example)
SUBWOOFER
(plays between
20Hz and 90Hz
in this example)