Filter
Top Products
18
Preparations
Speaker settings
Turn on the power to this receiver by pressing POWER or
ON/STANDBY key.
Select a speaker system.
1
2
1 Press the SET UP key such that the subwoofer setting
indication (SUBW ON) appears.
2 Use the MULTI CONTROL keys to select the appropriate
subwoofer setting.
1 SUBW ON: Subwoofer setting mode to the receiver is ON.
2 SUBW OFF: Subwoofer setting mode to the receiver is OFF.
• The initial setting is “SUBW ON”.
• When “SUBW OFF” is selected, the front speakers are automatically
set to “FRNT LRG” and the procedure skips to step 5.
•When subwoofer output sound is required, select “FRNT NML”.
3 Press the SET UP key again to accept the setting.
•The front speakers setting indication (FRNT) appears.
4 Use the MULTI CONTROL keys to select the appropriate front
speakers setting.
1 FRNT NML (normal): Average size front speakers are
connected to the receiver.
2 FRNT LRG (large): Large front speakers are con-
nected to the receiver.
•For “FRNT LRG” selection, no sound will be heard from SUBW
even when it is set to ON. However, if you select CINEMA EQ.
when subwoofer is selected, you will be able to hear sound from
the subwoofer.
When in STEREO mode, the sound goes directly to front speaker.
5 Press the SET UP key again to accept the setting.
•The center speaker setting indication (CNTR) appears.
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
If you have selected “NML” as the front speakers setting,
1 CNTR ON: Center speaker setting mode to the receiver
is ON.
2 CNTR OFF: Center speaker setting mode to the receiver
is OFF.
7 Press the SET UP key again to accept the setting.
•The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL keys to select the appropriate
surround speaker setting.
If you have selected “LRG” as the center speaker setting,
1 SURR LRG (large): Large surround speakers are con-
nected to the receiver.
2 SURR NML (normal): Average size surround speakers are
connected to the receiver.
3 SURR OFF: Surround speaker setting mode to the
receiver is OFF.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
6 Use the MULTI CONTROL keys to select the appropriate center
speaker setting.
If you have selected “LRG” as the front speakers setting,
1 CNTR LRG (large): A large center speaker is connected to
the receiver.
2 CNTR NML (normal): An average size center speaker is con-
nected to the receiver.
3 CNTR OFF: Center speaker setting mode to the
receiver is OFF.
Preparing for surround sound
If you have selected other than “LRG” as the center speaker
setting,
1 SURR ON: Surround speaker setting mode to the
receiver is ON.
2 SURR OFF: Surround speaker setting mode to the
receiver is OFF.
9 Press the SET UP key again to accept the setting.
•The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected channels
of the speakers that require adjusting.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
MULTI CONTROL
SET UP
RC-R0616
SET UP
RC-R0512
MULTI
CONTROL
POWER
ON/STANDBY
The channel indication blinks while the test tone is being output.
STEREO
R
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
L
SP A
3
Adjust the speaker volume.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1 Use the MULTI CONTROL keys to adjust the volume of the
test tone output from the speaker channel to be adjusted.
The test tone is heard from the speakers for 2 seconds at
a time in the following sequence for 2 seconds each:
L = C = R = SR = SL = SW
•If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed. º
•If the speaker setting selects are changed, the speaker level
settings are reset.
2 Press the SET UP key.
•The test tone is turned off. The receiver enters the mode for
inputting the distance to the speakers.