Filter
Top Products
LVT2123-029A[US/UX/UG/UW]
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
Front: No obstructions and open spacing.
Sides/Top/Back: No obstructions should be placed in the areas indicated by the dimensions in
the illustration.
Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a
stand with a height of 10 cm or more.
1.
2.
3.
ENGLISH (1/2)
1
Canceling the display demonstration
When you plug in and turn on the System, the display
demonstration starts automatically if no operation is done
for about 2 minutes.
To cancel the display demonstration
MICRO COMPONENT SYSTEM
UX-F4VB
—consists of CA-UXF4VB and SP-UXF4VB
Prepare the remote control
When you use the remote control for the first time, pull out the insulation sheet.
To replace the battery in the remote control
❍
Supplied accessories
After unpacking, check to make sure that you have all
the following items:
Remote control (× 1)
Lithium coin battery CR2025 (× 1)
The battery has been installed in the remote
control when shipped from the factory.
FM antenna (× 1)
AM loop antenna (× 1)
Composite video cord (× 1)
AC plug adaptor (× 1)
(not supplied for Middle Eastern and Saudi Arabian
models)
If anything is missing, consult your dealer immediately.
❍
•
•
–
•
•
•
•
Lithium coin battery
(product number: CR2025)
NOTES:
Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor
immediately.
To prevent the battery from overheating, cracking, or starting a fire:
Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.
Do not leave the battery with other metallic materials.
Wrap the battery with tape and insulate when throwing away or saving it.
Do not poke the battery with tweezers or similar tools.
Dispose of battery in the proper manner, according to federal, state, and local regulations.
The battery (battery pack or battery installed) shall not be exposed to excessive heat source such as sunshine, fire or
the like.
•
•
–
–
–
–
•
•
Getting started
For better FM reception
Disconnect the supplied FM antenna, and connect to an outdoor FM antenna
(not supplied) using a 75 Ω wire with coaxial type connector.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
FM antenna (supplied): Extend it so that you can obtain the best reception.
Precautions
Notes on the power cord
When you go away for an extended period of time,
remove the plug from the wall outlet.
When unplugging the System from the wall outlet,
always pull the plug, not the power cord.
Do not handle the power cord with wet hands.
Disconnect the power cord before cleaning the System or
moving the System.
Do not alter, twist or pull the power cord, or put anything
heavy on it, which may cause fire, electric shock, or other
accidents.
Avoid moisture, water, dust, and high temperatures
Do not place the System in moist or dusty places.
If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult your
dealer. Using the System in this state may cause a fire or
electrical shock.
Do not expose the System to direct sunlight or place it
near a heating device.
Notes on installation
Select a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
Do not install the System in a place subject to vibrations.
Do not put heavy objects on the System.
To prevent malfunction or damage to the System
Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
Do not block the vents.
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
•
•
•
•
•
•
•
•
•
•
•
•
•
NOTES:
Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away from metallic parts of the System,
connecting cords, and the AC power cord. Otherwise, it could cause poor reception.
When connecting the speaker cords, match the polarities of the speaker terminals: red to (+) and black to (–).
DO NOT connect more than one speaker to each terminal.
Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the System.
DO NOT allow the conductor of the speaker cords to come into contact with the metallic parts of the System.
The speakers are magnetically shielded to avoid color distortions on TVs. However, if not installed properly, it may cause color distortions. Therefore, pay attention to the following
when installing the speakers.
When placing the speakers near a TV set, turn off the TV’s main power switch or unplug it before installing the speakers.
Then wait at least 30 minutes before turning on the TV’s main power switch again.
Some TVs may still be affected even though you have followed the above instructions. If this happens, move the speakers away from the TV.
Connect your TV directly to the System. Connecting the System to a TV via a VCR or an HDD DVD recorder may interfere with your viewing. Connecting an integrated TV/VCR system
to the System may also interfere with your viewing.
•
•
•
•
•
•
–
–
•
Initial settings
Specifications
0510YOMMDWCDT
©2010 Victor Company of Japan, Limited
For turning off the demonstration display, see
“Canceling the display demonstration” in “Initial
settings.”
Thank you for purchasing a JVC product.
CD-R/-RW: Recorded in the Audio CD, Video CD, and
SVCD formats. MP3, WMA, JPEG, MPEG-1, MPEG-2, and
DivX*
1
files written in accordance with the “ISO 9660”
format can also be played.
DVD-R/-RW, +R/+RW: Recorded in the DVD Video format.
MP3, WMA, JPEG, MPEG-1, MPEG-2, and DivX*
1
files
written in the UDF-Bridge format can also be played.
DVD-R/-RW: Recorded in the DVD Video Recording (VR)
format.
USB mass storage class device, SD/SDHC card: MP3, WMA,
JPEG, MPEG-1, MPEG-2, and DivX*
1
files.
In addition to the above discs/files, this System can play
back audio data recorded on CD-Extra.
The following discs cannot be played back: DVD-RAM,
CD-I (CD-I Ready) and Photo CD. Playing back these discs
will generate noise and damage the speakers.
It is possible to play back finalized +R/+RW (DVD Video
format only) discs. The DVD indicator lights up when a
+R/+RW disc is loaded.
“DVD Logo” is a trademark of DVD Format/Logo Licensing
Corporation.
The System recognizes up to 999 tracks (files) and 130
groups.
*
1
Maximum resolution:
720 × 480@30fps / 720 × 576@25fps
•
•
•
•
For MP3/WMA playback...
Some MP3/WMA files may not be played back due to
their recording conditions.
This System can play only a disc of ISO 9660 Level 1 or
Level 2.
It is recommended to record each file at a sampling rate
of 44.1 kHz and at a data transfer rate of 128 kbps.
This System cannot play back files made at a bit rate of
less than 64 kbps.
This System can show the Tag data (Version 1).
For playback of files on a USB mass storage class device/
SD card...
You cannot play back files larger than 2 GB.
This System may not play back some USB mass storage
class devices/SD cards and does not support DRM
(Digital Rights Management).
This System can play back files on DVD, CD*
2
, USB mass
storage class device*
2
and SD/SDHC card*
2
recorded
by JVC EVERIO camcorders with the extension <.mod>.
These files cannot be played back if HD format is used.
*
2
Only when the maximum bit rate is less than 2 Mbps.
About color system
Connect a PAL or NTSC TV to this System.
This System can play back discs recorded in PAL and
NTSC video format.
Note on Region Code
DVD players and DVDs have their own Region Codes.
This System can play back only DVDs with an appropriate
Region Code.
Country/area Region Code
Middle East and Saudi Arabia 2
Southeast Asia 3
Central and South America 4
Ex.: For Southeast Asia
“RG ERROR” appears if a DVD with an incompatible
Region Code is loaded.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard. Therefore, the
use of the Non-DVD side of a DualDisc in this product may
not be recommended.
•
–
–
–
–
–
•
–
–
•
•
•
•
Playable disc/file types
INSTRUCTIONS
Setting the clock
1
If you have already set the clock before, press CLOCK
repeatedly until the clock setting mode is selected.
2 Adjust the hour and minute.
To go back to the previous step, press CANCEL while
holding SHIFT.
The clock may gain or lose 1 to 2 minutes per month. You
may need to readjust the clock periodically.
•
•
•
In this manual...
The remote control buttons are used for explaining the
operations unless mentioned otherwise. However, if the
System has the same or similar button names, they can
also be used for the operations.
The English on-screen displays and terms are used for
explanation though you can change the on-screen
language.
“SD card” refers to both SD card and SDHC card.
“File” and “track” are used interchangeably.
•
•
•
•
Main unit—CA-UXF4VB
Output Power: 100 W (50 W + 50 W) at 6 Ω (10% THD)
Audio Input: AUDIO IN: Stereo mini (ø 3.5 mm)
Microphone Input: MIC: Monaural mini (ø 3.5 mm)
Audio output: SUBWOOFER OUT: 500 mV/10 kΩ
Digital output: OPTICAL DIGITAL OUT:
–21 dBm to –15 dBm (660 nm ±30 nm)
VIDEO OUT × 1
COMPONENT VIDEO OUT × 1
Speaker impedance: 6 Ω – 16 Ω
Tuner
FM frequency: 87.50 MHz – 108.00 MHz
AM frequency
For Saudi Arabia: 531 kHz – 1 602 kHz
(at 9 kHz intervals)
530 kHz – 1 600 kHz
(at 10 kHz intervals)
For other countries/areas: 531 kHz – 1 710 kHz
(at 9 kHz intervals)
530 kHz – 1 710 kHz
(at 10 kHz intervals)
USB
USB specification: Compatible with USB 2.0 Full Speed
Compatible device: Mass storage class
Compatible system: FAT16, FAT32
Output power: DC 5 V
500 mA
SD
Compatible device: SD, SDHC
Compatible system: FAT16, FAT32
Setting the scanning mode
Select the video signal output setting according to the
type of your TV.
You can set the scanning mode only when “DVD/CD,”
“USB,” or “SD” is selected as the source.
Select “INTERLACE-YUV” when you have connected your
TV to the System using a composite video cord.
•
•
OPTICAL
DIGITAL
OUT
OPTICAL
DIGITAL
OUT
Optical digital cord
(not supplied)
When playing multi-channel encoded software,
the System properly converts the multi-channel
signals into 2 channels, and emits the downmixed
sound from the speakers. To enjoy the powerful
sound of the multi-channel encoded software,
connect a proper decoder or an amplifier with
a built-in decoder to the OPTICAL DIGITAL OUT
terminal.
Set “AUDIO OUT” in the “
” menu correctly
according to the connected digital audio
equipment (see “Setup menu operations of the
System” on page 4).
The digital signal is transmitted through the
OPTICAL DIGITAL OUT terminal when “DVD/CD,”
“USB,” or “SD” is selected as the source.
•
•
•
From the powered
subwoofer
(not supplied)
Before connecting the
System to the power supply,
make sure that the powered
subwoofer is turned off.
P-SCAN YPBPR
For a progressive TV.
Select to enjoy a progressively
scanned picture through the
COMPONENT VIDEO OUT jacks.
PRGR. (Progressive) indicator lights
up.
•
INTERLACE-
YUV
For a conventional TV.
Select when connecting the TV through
the VIDEO OUT jack.
After connecting a TV, select the appropriate video signal
output setting according to the connection method. See
“Setting the scanning mode” in “Initial settings” below.
(On the main unit)
(Hold)
DIGITAL VIDEO
P
B
Y
P
R
SUPER VIDEO
COMPACT
DIGITAL AUDIO
Component video
cord (not supplied)
Green
Red
Blue
SUPER VIDEO
General
Power source: AC 110 V– 127 V/AC 220 V– 240 V
(adjustable with the voltage selector), 50 Hz/60 Hz
Power consumption (at operation): 45 W
Power consumption (on standby): 1.00 W or less
Dimensions (approx.) (W × H × D) (including projecting
parts): 236 mm × 123 mm × 285 mm
Mass (approx.): 2.0 kg
Speaker—SP-UXF4VB
Speaker type: Bass-reflex type (Magnetically-shielded type)
Tweeter: 4 cm
Woofer: 12 cm
Impedance: 6 Ω
Dimensions (approx.) (W × H × D) (including projecting
parts): 141 mm × 250 mm × 181 mm
Mass (approx.): 2.2 kg each
Supplied accessories
See “Supplied accessories” in “Getting started.”
Design and specifications are subject to change without
notice.
Front view
Main unit
Speaker Speaker
Side view
Main unit
Connections Do not connect the AC power cord until all other connections have been made.
Maintenance
To get the best performance of the System, keep your discs
and the mechanism clean.
Handling discs
Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
Do not touch the shiny surface of the disc, or bend the
disc.
Put the disc back in its case after use.
Be careful not to scratch the surface of the disc when
placing it back in its case.
Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
Stains should be wiped off with a soft cloth. If the System
is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe
clean with a dry cloth.
Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
DO NOT wipe it hard.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substances such as
insecticides to it.
DO NOT allow any rubber or plastic to remain in contact
for a long time.
•
•
•
•
•
•
•
–
–
–
–
Connect your TV to the System using either a composite video cord
or component video cord.
From
left
speaker
From
right
speaker
(While holding...)
INTERLACE-YUV
On the TV screen
Red
Black
Composite video cord
(supplied)
P-SCAN YPBPR
INTERLACE-YUV
NOTE:
Keep the AM loop antenna cable wrapped around the
AM loop antenna frame, otherwise the effectiveness
and sensitivity of the AM loop antenna may be
reduced.
AM loop antenna
(supplied)
Yellow
To a wall outlet
If a wall outlet does not match the AC plug, use the
supplied AC plug adaptor (not supplied for Middle
Eastern and Saudi Arabian models).
•
When you connect a TV using a component video cord,
you can enjoy a high quality picture by selecting the
progressive scanning mode. To select the scanning
mode, see “Setting the scanning mode” in “Initial
settings” below.
CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC)
line voltage corresponds with the position of the
voltage selector switch provided on the outside of this
equipment and, if different, reset the voltage selector
switch, to prevent from a damage or risk of fire/electric
shock.
Voltage selector switch
(on the bottom of the System)
Turn it until the best reception
is obtained.
Red
Black
Black
White
EN_UXF4VB[USUXUGUW].indd 1EN_UXF4VB[USUXUGUW].indd 1 10.5.10 7:49:02 PM10.5.10 7:49:02 PM