JVC KS-AX4302 Stereo Amplifier User Manual


 
1
KS
-
AX4504
KS
-
AX4302
POWER AMPLIFIER: INSTRUCTIONS
AMPLIFICATEUR DE PUISSANCE: MANUEL D’INSTRUCTIONS
0107MNMMDWTKC
EN, FR
© 2007 Victor Company of Japan, Limited
ENGLISH
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specifi c car. If you have any questions or require information regarding
installation kits, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer or a company
supplying the kits.
A Mount this unit on a fi rm surface, such as in the trunk room or under the front seat.
Since heat is generated in the unit, do not mount it near infl ammable objects. In addition,
mount it in an area that will not prevent the unit from dissipating the heat.
Do not mount the unit in the places subject to heat: near a radiator, in a glove compartment
or in insulated areas such as under a car mat that will prevent the unit from dissipating heat.
When mounting the unit under the front seat, make sure that adjusting the seat position will
not catch any wire of the unit.
B When mounting this unit, be sure to use the provided screws. If any other screws are used,
there is a risk of loosening the unit or damaging parts inside it.
Before drilling holes in the trunk to install the unit, make sure that there is a suffi cient space
under the trunk so that you do not drill holes in the fuel tank, etc.
To detach and rotate the Logo Plate 180 degrees, use the provided hex wrench (3 mm).
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
For safety....
Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
• Stop the car before performing any complicated operations.
CAUTIONS AND NOTES
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
• This unit uses BTL (Balanced Transformerless) amplifi er circuitry, i.e., fl oating ground system,
so please comply with the following:
Do not connect the “·terminals of the speakers to each other.
Do not connect the “·terminals of the speakers to the metal body or chassis.
• Cover the unused terminals with insulating tape to prevent them from short circuiting.
When an extension lead is used, it should be as thick and short as possible; connect it fi rmly
with insulating tape.
• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
When replacing the fuse, only use a 25 A fuse for KS-AX4504 or a 20 A fuse for KS-AX4302.
• Do not let pebbles, sand or metallic objects get inside the unit.
To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off periodically.
• Listening to the tape, radio, CD or Digital Audio Player, etc. with the volume set at a high level
for a long period of time will exhaust the battery, while the engine is turned off or while the
engine is idling.
• This unit becomes very hot. Be careful not to touch the unit not only when using but for a while
after using.
DO NOT disassemble the units since there are no user serviceable parts inside.
CAUTION
To prevent short circuits while making connections, keep the battery’s negative terminal
disconnected.
• When using a power cord (purchased separately), be sure to place the 30 A fuse near the
battery as shown.
• Connect the lead wire (power cord) through which power is supplied directly to the battery’s
ªterminal only after all the other connections have been made.
The proper lead wire connected to each POWER terminal is as follows.
• + B and GND: AWG 8 to AWG 4 (The cross section is about 8 mm
2
to
21 mm
2
.)
• REM: AWG 18 to AWG 8 (The cross section is about 0.8 mm
2
to
8 mm
2
.)
• If you have any questions regarding the thickness of the power cord, etc., consult your nearest
“JVC IN-CAR ENTERTAINMENT” car audio dealer.
a When you use JVC car receiver with a remote lead, connect to the REM terminal on this
unit.
b When you connect a unit without a remote lead, connect to the accessory circuit of the
car which is activated by the ignition switch. In this case, noise may occur when the car
receiver is turned on or off. To avoid this noise, do not turn on or off the car receiver itself.
You can turn on or off the car receiver along with the on/off operation of the ignition switch.
If the POWER/PROTECTOR lamp lights in red, it indicates incorrect speaker wiring or
connections (see "TROUBLESHOOTING" on page 3). Make sure to correct speaker wiring and
other connections.
TERMINAL CONNECTIONS
When making the terminal connections…
1 Peel the insulating vinyl cover of a cord 7 mm (
5
/16 in.) to 10 mm
(
7
/16 in.) long and expose the inside conductor.
2 Loosen the hex screw in a terminal with a provided hex wrench
and insert the conductor into the terminal. Then fi x the hex screw
again to secure the conductor.
Note
• The exposed conductor should be 7 mm (
5
/16 in.) to 10 mm (
7
/16 in.) long.
– If shorter, it may cause a poor conductivity.
– If longer, it may cause a short circuit.
• Use a proper hex wrench for each terminal.
– 4 mm: +B terminal and GND terminal
– 3 mm: Speaker terminals of KS-AX4302 and REM terminal
– 2 mm: Speaker terminals of KS-AX4504
POWER SUPPLY
LVT1696-001A
[J/E/U]
AB
SPEAKER SYSTEMS
This amplifi er provides two types of speaker connections: Normal Mode and Bridge Mode. You
can choose either type of connections depending on the speakers confi guration equipped on
your car.
Make sure to comply with the following notes:
• Be sure not to connect the “·terminals of the speakers to a common point.
• If the ground wire is common to both left/right and front/rear speaker wirings, this unit cannot be
used. Always use the independent lead wires for the speakers to be used. In this case, redo the
wirings.
• Use the speakers with an impedance of 2 to 8 (4 to 8 : when used in Bridge Mode).
• Use the speakers which have suffi cient capacity to the unit.
The proper lead wire connected to each SPEAKER OUTPUT terminal is as follows.
• KS-AX4504: AWG 18 to AWG 12 (The cross section is about 0.8 mm
2
to
3.3 mm
2
.)
• KS-AX4302: AWG 18 to AWG 8 (The cross section is about 0.8 mm
2
to
8 mm
2
.)
For KS-AX4504:
When you connect 4 speakers to the unit, down mixed signals (front and rear) are emitted
through the PRE OUT jacks.
For KS-AX4302:
Incoming signals are emitted through the PRE OUT jacks.
For Customer Use:
Enter below the Model No. and Serial No. which
are located on the top or bottom of the
cabinet. Retain this information for future reference.
Serial No.
Logo Plate (detachable)
Model No.
EN_KS-AX4504_4302[JEU].indd 1EN_KS-AX4504_4302[JEU].indd 1 07.1.25 11:23:07 AM07.1.25 11:23:07 AM