Filter
Top Products
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
Front: No obstructions and open spacing.
Sides/Top/Back: No obstructions should be placed
in the areas indicated by the dimensions in the
illustration.
Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
1.
2.
3.
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
•
•
•
•
Front view
Side view
LVT2114-015A[US/UB/A/UJ]
0310YAMMDWDAT
©2010 Victor Company of Japan, Limited
1
Sleep Timer
Specify the time (in minutes).
To check the remaining time until the System shuts off,
press SLEEP once.
Daily Timer
By using Daily Timer, you can wake up with your favorite
music.
Set the clock before using Daily Timer (see “Setting the
clock” in “Initial settings”).
You can store three Daily Timer settings.
Tune into a station, insert a disc, or connect a USB mass
storage class device/iPod to the System beforehand.
1 Select a Daily Timer number.
2
3
Set the timer contents.
Hour and minute for the on-time and off-time
Playback source
For “TUNER FM”: Select a preset number. (To preset
stations, see “Presetting stations” in “FM radio” on
page 2).
For “CD” or “USB”: Select a track number. (For MP3/
WMA: Select a group, then a track number.)
Volume
To correct a misentry during the process, press
CANCEL. You can return to the previous step.
•
•
•
•
–
–
•
•
–
•
4 Press TIMER repeatedly to exit from the setting.
5 Turn off the System.
The STANDBY lamp starts flashing.
While on standby, the timer indicator ( ) is not
displayed.
To cancel a Daily Timer
1 Select a Daily Timer number.
2 Cancel the selected Daily Timer.
The timer indicator is turned off.
The timer contents are kept.
3 Press TIMER repeatedly to exit from the setting.
Auto Standby
You can turn off the System automatically.
“A.STBY” and “SET” appear alternately.
The A.STBY indicator starts flashing after playback
stops. If no operation is done for about 3 minutes, the
System is turned off.
This function cannot be used when “TUNER FM” or
“AUDIO IN” is selected as the source.
This function does not work when Sleep Timer is
activated.
•
•
•
•
•
Lithium coin battery
(product number: CR2025)
Sound adjustments
Fade muting
To drop the volume in a moment
To restore the volume, press again or adjust the
volume level.
Sound Turbo
To emphasize the sound
Hyper Bass Sound (HBS)
To reinforce the bass sound
Bass and treble levels
1
2
Adjust the level.
❍
•
Display settings
Display/illumination brightness
You can dim the display window and illumination.
Display information
You can change the information shown on the display.
Ex.: During playback of a CD...
The information shown on the display differs
depending on the source.
❍
•
Compatible iPod models
iPod model Audio Video
iPod nano
–
iPod nano (2nd Generation)
–
iPod nano (3rd Generation)
iPod nano (4th Generation)
iPod nano (5th Generation)
iPod mini –
iPod mini (2nd Generation)
–
iPod (4th Generation)
–
iPod classic
iPod photo (4th Generation) *
iPod video (5th Generation)
iPod touch
iPod touch (2nd Generation and Fall ‘09)
Only for still picture
If iPod does not play correctly, update iPod software to the
latest version.
For details about updating iPod, check on the Apple web
site <http://www.apple.com>.
*
•
Canceling the display demonstration
When you plug in and turn on the System, the
display demonstration starts automatically if no
operation is done for about 2 minutes.
To cancel the display demonstration
Setting the clock
1
“CLOCK” and “ADJUST” appear alternately.
2
3
Adjust the hour and minute.
To go back to the previous step, press CANCEL.
The clock is not shown on the display until you
set it.
The clock may gain or lose 1 to 2 minutes per
month. You may need to readjust the clock
periodically.
•
•
•
MICRO COMPONENT SYSTEM
UX-SG5B
—consists of CA-UXSG5B and SP-UXSG5B
Supplied accessories
After unpacking, check to make sure that you have all
the following items:
Remote control (× 1)
Lithium coin battery CR2025 (× 1)
The battery has been installed in the remote
control when shipped from the factory.
FM antenna (× 1)
Composite video cord (× 1)
AC plug adaptor (× 1) (not supplied for Australian
and Hong Kong models)
If anything is missing, consult your dealer immediately.
❍
•
•
–
•
•
•
Notes on the power cord
When you go away for an extended period of time,
remove the plug from the wall outlet.
When unplugging the System from the wall outlet,
always pull the plug, not the power cord.
Do not handle the power cord with wet hands.
Disconnect the power cord before cleaning the System or
moving the System.
Do not alter, twist or pull the power cord, or put anything
heavy on it, which may cause fire, electric shock, or other
accidents.
Avoid moisture, water, dust, and high temperatures
Do not place the System in moist or dusty places.
If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult your
dealer. Using the System in this state may cause a fire or
electrical shock.
Do not expose the System to direct sunlight or place it
near a heating device.
•
•
•
•
•
•
•
•
NOTES:
Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor
immediately.
To prevent the battery from overheating, cracking, or starting a fire:
Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.
Do not leave the battery with other metallic materials.
Wrap the battery with tape and insulate when throwing away or saving it.
Do not poke the battery with tweezers or similar tools.
Dispose of battery in the proper manner, according to federal, state, and local regulations.
The battery (battery pack or battery installed) shall not be exposed to excessive heat source such as sunshine, fire or
the like.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
•
•
–
–
–
–
•
•
Getting started
For better FM reception
Disconnect the supplied FM antenna, and connect to an outdoor FM antenna
(not supplied) using a 75 Ω wire with coaxial type connector.
Red
Black
From left speaker
From right speaker
FM antenna (supplied): Extend it so that you can obtain the best reception.
Maintenance
To get the best performance of the System, keep your discs
and the mechanism clean.
Handling discs
Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
Do not touch the shiny surface of the disc, or bend the
disc.
Put the disc back in its case after use.
Be careful not to scratch the surface of the disc when
placing it back in its case.
Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
Stains should be wiped off with a soft cloth. If the System
is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe
clean with a dry cloth.
Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
DO NOT wipe it hard.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substances such as
insecticides to it.
DO NOT allow any rubber or plastic to remain in contact
for a long time.
•
•
•
•
•
•
•
–
–
–
–
NOTES:
Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord.
Also, keep the antennas away from metallic parts of the System, connecting cords, and the AC power
cord. Otherwise, it could cause poor reception.
When connecting the speaker cords, match the polarities of the speaker terminals: red to (+) and black to
(–).
DO NOT connect more than one speaker to each terminal.
Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of
the System.
DO NOT allow the conductor of the speaker cords to come into contact with the metallic parts of the
System.
•
•
•
•
•
Sound and other adjustments
Precautions
Connections Do not connect the AC power cord until all other connections have been made.
For turning off the demonstration display, see
“Canceling the display demonstration” in “Initial
settings.”
Thank you for purchasing a JVC product.
INSTRUCTIONS
In this manual...
The remote control buttons are used for explaining the
operations unless mentioned otherwise. However, if the
System has the same or similar button names, they can
also be used for the operations.
“File” and “track” are used interchangeably.
•
•
Specifications
Main unit (CA-UXSG5B)
General
Power source: AC 110 V – 240 V, 50 Hz/60 Hz
Power consumption (in operation): 16 W
Power consumption (on standby): 1.00 W or less
Dimensions (W × H × D) [including projecting parts]:
165 mm × 250 mm × 226 mm
Mass: 2.3 kg
Audio output
Analog sound output:
Speakers × 2
Output power
(IEC 268-3): 40 W (20 W + 20 W) at 6 Ω (10% THD)
Fitting impedance: 6 Ω – 16 Ω
Audio input
Sound input:
AUDIO IN × 1
NORMAL: 500 mV/47 kΩ
HIGH: 250 mV/47 kΩ
iPod × 1: DC 5 V
500 mA
USB
Compatible with USB 2.0 Full-Speed
Compatible device: USB mass storage class device
Compatible file system: FAT16, FAT32
Output power: DC 5 V 500 mA
Tuner
FM tuner:
Receiving frequency: 87.50 MHz to 108.00 MHz
Antenna: 75 Ω - unbalanced type
Speaker (SP-UXSG5B)
Type: Bass-reflex type
Speaker: Full range: 10 cm
Power handling capacity: 20 W
Impedance: 6 Ω
Dimensions (W × H × D) [including projecting parts]:
140 mm × 250 mm × 134 mm
Mass (1 speaker): 1.3 kg
Supplied accessories
See “Supplied accessories” in “Getting started.”
Design and specifications are subject to change without
notice.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Red
(On the main unit)
(Hold)
Main unit
Speaker Speaker
Main unit
Troubleshooting
If you are having a problem with your System, check this list for a possible solution before calling for service.
General
Power does not come on. \ Power plug is not inserted securely. Plug it in securely.
Adjustments or settings are suddenly
canceled before you finish.
\ There is a time limit. Start the procedure again.
Unable to operate the System from the
remote control.
\ The path between the remote control and the remote sensor on the
System is blocked.
\ The battery is exhausted.
No sound is heard. \ Speaker connections are incorrect or loose.
\ Headphones are connected.
FM radio
Hard to listen to broadcasts because of
noise.
\ Antenna connection is incorrect or loose.
\ The FM antenna is not properly extended and positioned.
\ Electrostatic discharge from your body may cause noise. If this
happens, turn the System off then on again.
iPod
The iPod does not play, but “CONNECT”
appears on the display.
\ The iPod battery is low or exhausted. Charge the iPod battery.
“PLEASE IPOD CHECK” appears on the
display.
\ The iPod is not connected properly.
Disc/USB
The disc/USB mass storage class device
does not play.
\ The disc is placed upside down. Place the disc with the label side
facing up.
\ The disc is recorded using “packet writing (UDF file system).” It cannot
be played.
\ The USB mass storage class device is not connected properly.
“NO FILE” appears on the display. \ MP3/WMA files are not recorded on the disc or USB mass storage class
device.
Groups and tracks are not played back as
you expect.
\ Playing order is determined when the groups and tracks are recorded.
It depends on the writing application.
The disc/USB mass storage class device
sound is discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly recorded onto the USB mass
storage class device.
Sound from the USB mass storage class
device is interrupted.
\ Noise and static electricity may stop the sound. In this case, disconnect
and connect the USB mass storage class device again after turning off
the System.
The disc tray does not open or close. \ The AC power cord is not plugged in.
\ Disc ejection is prohibited. “LOCKED” appears (see “Prohibiting disc
ejection” in “Disc/USB” on page 2).
Timers
Daily Timer does not work. \ The System was turned on when the on-time came. The timer starts
working only when the System is turned off.
\ When you unplug the AC power cord or if a power failure occurs, the
timer will be canceled. You need to set the clock first, then the timer
again. (See “Setting the clock” in “Initial settings” and “Daily Timer” in
“Timers” on the right.)
If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, then
connect the cord again.
JVC bears no responsibility for any loss of data in USB mass storage class device or iPod while using this System.
•
•
Initial settings
DIMMER 2DIMMER 1
DIM OFF
Current track’s elapsed time Clock
TURBO ON
TURBOOFF
HBS ON
HBS OFF
Timers❍
CLOCK ADJUSTExit from the setting
TIMER-1 TIMER-2 TIMER-3
Monitor
To view video/picture from the iPod
Playable disc/file types
This System can play back...
Audio CD and CD-R/CD-RW in Audio CD format
MP3/WMA files on a CD-R/CD-RW (ISO 9660 format) or
USB mass storage class device (maximum data transfer
rate: 2 Mbps)
This System cannot play “packet write” discs.
This System can recognize up to 99 groups and 999 tracks
on a disc and USB mass storage class device.
For MP3/WMA playback...
Some MP3/WMA files may not be played back due to
their recording conditions.
This System can play only discs of ISO 9660 Level 1 or
Level 2.
It is recommended to record each file at a sampling rate
of 44.1 kHz and at a data transfer rate of 128 kbps.
This System cannot play back files made at a bit rate of
less than 64 kbps.
This System can show the Tag data.
For playback of files on a USB mass storage class device...
You cannot play back files larger than 2 GB.
This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
•
–
–
•
•
•
–
–
–
–
–
•
–
–
Composite video
cord (supplied)
To a wall outlet
If a wall outlet does not match the AC plug, use the supplied AC plug adaptor
(not supplied for Australian and Hong Kong models).
•
Exit from the setting CLOCK ADJUST
TIMER-1 TIMER-2 TIMER-3
BASS
TREB
SLEEP 10 SLEEP 20 SLEEP 30
SLEEP180
SLEEPOFF
To composite video input
Prepare the remote control
When you use the remote control for the first time, pull out the insulation sheet.
To replace the battery in the remote control
❍
ENGLISH
(Hold)
A.STBY SET A.STBY CANCEL
Notes on installation
Select a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
Do not install the System in a place subject to vibrations.
Do not put heavy objects on the System.
To prevent malfunction or damage to the System
Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
Do not block the vents.
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
•
•
•
•
•
Do not unplug the AC power cord before turning off the System. Some of the settings you have
made will be lost if you do so.
EN_UXSG5B[USUBAUJ]f.indd 1EN_UXSG5B[USUBAUJ]f.indd 1 10.3.8 8:34:29 PM10.3.8 8:34:29 PM