Filter
Top Products
Connecting the headphones
Caution: To prevent damage to your system, make sure that all
components are turned o before making the connections. The
following diagram shows a typical user installation.
In this example the docking station is connected to the audio
output of a TV and the audio input of a stereo system
(optional). This optional connection is helpful if your audio
source component only has one audio output and you want to
connect it to both the docking station and another
component, like a stereo system.
Note: If your audio device does not have RCA outputs, you can use the
3.5 mm-to-RCA adapter (included) to make the connections. Your
setup may dier from the example shown here.
Connecting the AC adapter to the docking station
1 Connect the AC adapter connector to the docking station’s DC 5V jack.
2 Connect the AC adapter plug to an AC power outlet.
3 Turn the ON/OFF switch on the back of the docking station to “ON.”
The PAIRING indicator begins to blink (blue).
Package contents
Headphones
and docking station
User Guide
3.5 mm-to-RCA
adapter cable
AC power adapter
RCA audio cable
Quick Setup Guide
INSIGNIA is a trademark of Best Buy and its aliated companies. Registered in some countries.
Distributed by Best Buy Purchasing, LLC., 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V1 ENGLISH 14-0124
Charging the headphones
Important: Before using the wireless headphones for the rst time,
make sure that the batteries are fully charged for at least four hours.
To charge the headphones:
• Slide the OFF/ON switch on the docking station to ON.
• Place the headphones onto the docking station. Make sure that the
headphone charging contacts and the docking station charging pins
make contact by aligning the arrows (as shown below) when you put
the headphones in the charging station.
• The docking station Charging indicator turns red to indicate the
headphones are charging.
• When the headphones are fully charged (which takes
up to four hours), the docking station Charging
indicator turns green.
• When the headphone battery charge is low, the
Power/Pairing indicator on the headphones blinks
red. The Power/Pairing indicator on the headphones
turns red 30 minutes prior to the batteries being exhausted.
Notes:
• It can take up to four hours to charge the batteries. The batteries will last up to eight hours with continuous
use (depending on the headphone volume level and distance from the docking station).
• The headphones cannot be charged when the docking station is turned off.
Turning on and pairing your headphones
1 Slide the ON/OFF switch on the docking station to ON. The PAIRING indicator blinks (blue).
2 Press the (power) switch on the right earpiece to turn on the headphones. The
POWER/PAIRING indicator on the headphone blinks (blue).
3 When the POWER/PAIRING indicator on the headphones and the PAIRING indicator on the
docking station both light steadily blue, an active link is established between the headphone and
the docking station. The system is now on and ready to be used.
Notes:
• Autopairing takes 5-10 seconds.
• If the charge on the headphone batteries is low, the
POWER/PAIRING indicator on the headphones
blinks red. When this happens, you should charge the headphones.
Tip: If the power indicators on the headphones and docking station continue to blink after 30 seconds, they
are no longer paired to each other. If this happens, follow these steps:
• Make sure that the headphones and docking station are within range of each other (ideally in the same
room).
• Turn off the headphones and the docking station.
• Turn on both the headphones and the docking station. The lights will initially blink, then they should turn on
steady.
Listening to your digital wireless stereo headphones
1 Turn on the headphones and docking station. Make sure that your docking station and
headphones are wirelessly paired.
2 Set the headphone volume level to the minimum.
3 Put your headphones on your head. Adjust the t until you feel comfortable.
4 Turn on your audio source and begin playback. Depending on the audio source, you may
need to turn up the volume on the audio source.
5 Adjust the headphone volume to your normal listening level.
Caution: Continuous use at high volume may permanently damage your hearing.
Note: If the system is connected to a TV, you may want to turn o the TV sound to prevent hearing sound
from the TV speakers. Refer to your TV manual.
Turning o your headphones
1 Press and hold (more than two seconds) the (power) switch located on the headphones’
right earpiece to turn o the headphones.
2 Slide the ON/OFF switch on the docking station to OFF to turn o the docking station.
Note: It’s important to turn the headphones o when not in use to conserve the battery, or if you prefer
you can leave them on as long as they are placed in the docking station.
Specications
Input: AC 100-240V~ 50/60 Hz 0.2 A
Output: 5V, 500mA
One-year limited warranty
Visit www.insigniaproducts.com for details.
Contact Insignia:
For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
QUICK SETUP GUIDE
|
NS-WHP314
2.4 GHz Digital Wireless Stereo Headphones
Before using your new product, please read these instructions to prevent any damage.
Headphone arrow
Docking station arrow
Power/Pairing
button
Volume Up (+)
button
Power/Pairing
indicator
Volume Down (–)
button
Right earpiece
IN
Television Stereo system
Note: This is an
optional connection.