Harman-Kardon HS 350 Home Theater System User Manual


 
REMOTE CONTROL 29
ENGLISH
Remote Control
Learning Codes from a Remote
The HS 350 remote is able to “learn” codes from
other remote controls that might be part of your
system setup, like the one from your TV. To learn
or transfer codes from an IR remote to the HS’s
remote, follow these steps:
1. Place the front of the original remote with the
code being sent so that it is facing the IR
Transmitter Window
d
on the HS remote
“head-to-head.”The remotes should be between
2 and 4cm apart.
2. Select the button on the remote that you wish
to use as the device selector for the codes about
to be entered. This must be any of the Input
Selectors
0
.
3. Press the Input Selector
0
button chosen
and the Learn Button
X
at the same time.
Hold these buttons until the Program
Indicator
e
flashes amber and the light
under the device selector button turns red.
Release the buttons. It is important that you
begin the next step within 20 seconds.
4. Press the button on the HS remote that you
wish to program. Note that the Program
Indicator
e
will stop flashing.
Important Note: Codes cannot be taught to
all buttons on the remote. In these cases the
Program Indicator
e
keeps flashing after
the button was released.
5. As long as the Program Indicator
e
is on
steadily (for five seconds), press and hold the
button on the original remote that you wish to
“teach” into the HS remote. If you pressed the
button too late or no command was received
within five seconds, the Program Indicator
e
will flash red three times and then amber,
then simply repeat step four. When the
Program Indicator
e
turns green, release
the button on the original remote. Note that the
Program Indicator will then begin to flash amber
again.
NOTE: If the Program Indicator
e
turns red
steadily during Step 5, the programming was not
successful. Repeat the steps to see if the code
will “take.”If the indicator keeps flashing red in
step 5, this code cannot be taught.
6. Repeat steps 4 though 5 for each button on
the source remote that you wish to transfer to
the HS remote.
7. Once all codes have been transferred from the
original source remote to the HS remote, press
the Learn button
X
. This will turn off all LEDs
and turn off the learning mode.
8. Repeat Steps 1 through 7 for any additional
remotes you wish to “teach” into the HS
Remote.
Erasing Learned Codes
The HS’s remote allows you to remove or erase
the code learned into a single button for a single
device, to remove or erase all the codes that
have been learned for a single device, or to
erase all commands that have been learned to
all devices.
To erase a single learned code from within a
single device’s settings, follow these steps:
1. Press and hold both the Input Selector
0
within which the individual button to be erased
has been programmed and the
Learn button
X
.
2. When the red LED under the Input Selector
turns red and the Program Indicator
e
flashes amber, release the buttons.
3. Press and release the Input Selector
0
again for the device within which the individual
button to be erased has been programmed.
4. Press the 7 button
S
three times.
5. Press and release the individual button for
which the code is to be erased. The Program
Indicator
e
will blink green two times and
then return to amber.
6. To erase other buttons within the same
device, press them as noted in Step 5.
7. When all buttons to be erased have been
pressed, press the Learn button
X
to
complete the process.
To erase all codes within a single device, follow
these steps:
1. Press and hold both the Input Selector
0
for which you wish to erase the codes and the
Learn button
X
.
2. When the red LED under the Input Selector
turns red and the Program Indicator
e
flashes amber, release the buttons.
Macro Programming
Macros enable you to easily repeat frequently
used combinations of commands with the press
of a single button on the HS’s remote control.
Once programmed, a macro will send out up to
19 different remote codes in a pre-determined
sequential order enabling you to automate the
process of turning on your system, changing
devices, or other common tasks. The HS’s remote
can store up to four separate macro command
sequences, that are accessed by pressing the
Macro buttons
K
.
1. To start programming a macro, press the
Mute button
A
and the Macro button
K
to be programmed at the same time. Note that
the latest selected Input Selector will light red,
and the Program Indicator
e
will flash
amber.
2. Enter the steps for the macro sequence by
pressing the button for the actual command
step. Although the macro may contain up to 19
steps, each button press, including those used to
change devices, counts as a step.
The Program Indicator
e
will flash green
twice to confirm each button press as you enter
commands.
NOTE: While entering commands for Power On
of any device during a macro sequence, press
the Mute button
A
. DO NOT press the
Power ON button
0
.
• Remember to press the appropriate Input
Selector button
0
before functions are
changed to another device.
3. When all the steps have been entered, press
the Preset Up / PIC+ button
L
to enter the
commands. The red light under the Input
Selector
0
will blink and then turn off and
the Program Indicator
e
will flash green
twice to confirm the macro to be programmed.
0096CSK - HK HS 350 OM ENG.qxp:34252_HS350_Eng 20/01/09 10:38 Side 29