Filter
Top Products
15 PLAYBACK BASICS
Playback of CDs on the CDR 30 resembles that
for traditional CD players with a few exceptions
to accommodate the availability of two sepa-
rate playback decks. Before using the CDR 30,
power-up the unit by pressing in the Main
Power Switch 1. Note that the Standby
Mode Indicator 2 will turn green, indicating
that the unit is on and functioning.At the same
time, the Information Display ˜ will light,
the Time/Message DisplayF will briefly dis-
play HARMAN KARDON CDR 30 and the
legends behind the front panel controls will
also light up.
Once the Main Power Switch 1 has been
turned on, the CDR 30 may be powered-on
or -off using the remote control. Pressing the
Power-Off Button on the remote will
place the unit in a Standby mode, as indicated
by the amber color of the Standby Mode
Indicator 2.To turn the unit on using the
remote, simply press the Power-On Button a.
Note that when the unit is in the Standby mode,
it is still drawing power from the AC main
outlets.To turn the unit completely off, press
the Main Power Switch 1.When the
Standby Mode Indicator 2 goes out, the
CDR 30 is off and not drawing any power.
When you will not be using the unit for an
extended period of time, such as during a
vacation, we recommend using the Main
Power Switch 1 to turn the unit
completely off.
Although compact discs are very reliable, rough
handling may damage them.Avoid scratching
the bottom (nonprinted) side of the discs, as
this will affect playback of standard CDs and
interfere with the recording of CD-R and
CD-RW discs. It is also a good idea to always
handle discs by their edges to avoid fingerprints
which may also interfere with playback quality
and possibly cause damage to the laser and
lens assembly.
Loading and Unloading Discs
To load a disc, first open the desired CD deck
by pressing the appropriate Open/Close
Button 6$c`.The word OPEN will
appear in the Time/Message Display F.
Always make certain that there is sufficient
room in front of the unit for the disc drawers
to open. Note that if either disc drawer is
blocked, the drawer will stop at the blocked
position and an ERROR message will appear.
Press the appropriate Open/Close Button
6$c` to reopen the drawer.
Load a disc in the tray with the printed (label)
side facing up. Once the disc is seated, make
certain that it is properly centered within the
tray. When using 3" discs, take extra care to
make certain that the disc is carefully centered
within the smaller ridges in the disc tray.
To close the drawer, press the appropriate
Open/Close Button 6$c` or gently
press on the outside of the front cover of the
disc tray. When the drawer is closed the word
CLOSE will appear momentarily in the
Time/Message Display F, and the letters
TOC will begin to flash in the display once the
drawer is completely closed.
If the disc is a standard CD or a finalized CD-R
or CD-RW disc, TOC will flash while the unit
reads the disc’s Table of Contents information.
Once that data is read, the Time/Message
Display F will show the total number of
tracks and the total time of all tracks on the
disc.The CD Indicator Q will also light to
indicate that a standard CD is in use.
When an unfinalized CD-R or CD-RW disc is
placed in the Record Deck %, the letters
OPC will flash once the Table of Contents has
been read.This indicates that the unit is opti-
mizing its circuits for maximum compatibility
with the specific recordable disc in use.The
number and total running time of any tracks
that have already been recorded will appear in
the Time/Message Display F, and the
appropriate indicator Q will light to tell
you if a CD-R or CD-RW disc is in use.
If a computer data disc is placed in the CDR 30,
a DATA DISC or DISC ERROR mes-
sage will appear, depending on whether or not
the data disc is finalized. Data discs will not
play and cannot be recorded or dubbed on the
CDR 30.
Using the Remote
The CDR 30’s infrared remote control is
designed to operate both CD decks, as well as
control the playback programming and record
functions.To allow for efficient use of the
remote, its operation is different from standard
CD players. Some buttons are dedicated to one
specific CD deck, while others are shared
between the two decks.
No matter which deck is playing, the Play
Deck (CDP) and Record Deck (CDR)
Display b and Open/Close Buttons
c` will always send a command to their
respective deck.The other transport and pro-
gramming functions, however, are shared.To
use any of the transport controls, such as Play
j, Stop u, Pause v or the Search
and Skip Buttons fiwy, the
Numeric Keys o or the Programming
Keys eghkp, first press either the
CDP Button d to command the Play Deck
3 or the CDR Button z to command the
Record Deck %.When the button is pressed,
a message reading CDP or CDR will appear in
the appropriate Time/Message Display F
to confirm the selection.
To switch the remote from controlling one
deck to controlling the other, simply press the
Select Button dz for the deck you wish
to control at any time.
28
Labeled
Surface
29
Playback Basics