Filter
Top Products
48 PROGRAMMING THE REMOTE
Programming the Remote
the DEVICE IN USE on the left side of the bot-
tom line and the PUNCH-THROUGH device. In
the example used, the display to return the
remote to default settings will appear as shown
in Figure 58.
Figure 58
Transport Punch-Through
Transport punch-through allows the Play
P
,
Stop
P
, Fast Forward/Reverse
P
, Pause
P
, Record
P
and Skip Up/Down
R
but-
tons to send commands to a different device
than the one that has been selected for other
commands. For example, you may wish to oper-
ate the transport of a second VCR you have con-
nected to the VID 2/TV input, as shown in the
following example.
1. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 15 appears in the remote’s LCD
Information Display
2
. Release the but-
ton when the red light under the Set Button
F
appears.
2.The remote’s MAIN MENU message (Figure
16), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until PUNCH-THROUGH appears on the
bottom line of the LCD screen, as shown in
Figure 48. Press the Set Button
F
to enter
the main punch-through menu branch.
3.At the next menu screen, press the
⁄¤
Navigation Buttons
E
until TRANS-
PORT appears on the bottom line of the LCD
screen, as shown in Figure 59. Press the Set
Button
F
to begin programming the
remote for transport punch-through.
Figure 59
4.The next display screen (Figure 60) is where
you select the device that will receive the
punch-through commands. In our example,
that is the TV button, as that is where we want
the VCR’s transport controls to be active. Press
the
⁄¤
Navigation Buttons
E
until the
name of the base device appears and then
press the Set Button
F
.
Figure 60
5.At the next display screen (Figure 61), you will
select the device whose transport commands
will be used. Press the
⁄¤
Navigation
Buttons
E
until the desired device name
appears to the right of the device in use. In our
example, that is the VCR.When the desired
combination of devices appears, press the Set
Button
F
.
Figure 61
6.When the Set button is pressed, the display
will change to show you that the new combi-
nation of control commands is being saved to
the unit’s memory, as shown in Figure 62.The
word SAVED will flash four times and then
the remote will return to normal operation.
Figure 62
7. Once the punch-through is programmed, the
transport buttons of the second device named
will be used when those buttons are pressed
while the master device is in use.
Returning the Transport Control Settings
to Default Operation:
If you wish to remove the Transport Punch-
Through so that the transport commands are
returned to the factory default setting, follow the
steps shown above, except that in Steps 4 and 5,
select the same device for both the DEVICE IN
USE on the left side of the bottom line and the
PUNCH-THROUGH device. In the example used,
the display to return the remote to default set-
tings will appear as shown in Figure 63.
Figure 63
EzSet Configuration
Harman Kardon’s patented EzSet feature makes
it easier than ever to calibrate the output levels
on your new AVR for maximum playback accura-
cy. In addition to automatically setting the levels,
the AVR remote’s LCD display allows the unit to
be used as a direct read-out SPL meter. Complete
instructions for using the EzSet features of the
AVR remote are found on page 27 of this
owner’s manual.
In most cases you will find it easier to access the
EzSet capabilities directly by pressing the SPL
Select Button
e
and following the menu
prompts as detailed in page 27. However, there
is one function of the remote that is only avail-
able through the remote’s menu system being
described in this section.
To avoid having the calibration settings created
with EzSet changed accidentally, the remote
allows you to disable the SPL Select Button
e
on the remote. To de-activate the button,
follow these steps:
1. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 15 appears in the remote’s LCD
Information Display
2
. Release the but-
ton when the red light under the Set Button
F
appears.
2.The remote’s MAIN MENU message (Figure
16), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until SET SPKR LEVELS appears on the
bottom line of the LCD screen, as shown in
Figure 64. Press the Set Button
F
to enter
the main EzSet menu branch.
Figure 64
3.At the next menu screen (Figure 65) press the
⁄¤
Navigation Buttons
E
once so that
EZSET DISABLE appears in the lower line of
the LCD display.
Figure 65
4.Within five seconds, press the Set Button
F
to disable the SPL Select Button
e
.
Once the Set Button
F
is pressed the word
EXITING will flash four times in the lower line
of the LCD display and then it will return to
normal operation.
Once these steps are completed, when the SPL
Select Button
e
is pressed the remote will
show EZSET DISABLE and it will not be acti-
vated.
To restore the EzSet feature to normal operation,
repeat the procedure outlined above, except that
in step #3 you should press the
⁄¤
Navigation Buttons
E
so that EZSET
ENABLE appears in the lower line of the LCD
display. When that display appears, press the Set
Button
F
and the EzSet feature will be reacti-
vated.You may then press the Clear Button
X
to exit the remote’s menu system and return
to normal operation or press the Set Button
F
again to immediately use the EzSet feature
to calibrate the system as shown on page 27.
SET SPKR LEVELS
EZSET DISABLE
MAIN MENU
SET SPKR LEVELS
PUNCH-THROUGH
TV< -TV
TV< -VCR [TRS]
SAVED
PUNCH-THROUGH
TV< -VCR
DEVICE IN USE
TV
PUNCH-THROUGH
TRANSPORT
PUNCH-THROUGH
VCR< -VCR