Harman-Kardon 950-0321-001 Home Theater System User Manual


 
BDS
19
ENGLISH
Preparing the Remote Control
and Setting Up the Receiver
Setting Up the Receiver
NOTE: The menu screens shown in this manual are for illustrative purposes and may differ
somewhat from the actual displays.
To set up your BDS system, you will use the remote to navigate through all of the on-screen
menus and make selections from them.
Use the Cursor Up/Down buttons to navigate through the menu list. When an item is
t
highlighted, a border will appear around it.
To select a highlighted item, press the OK button. The screen will change depending on
t
your selection.
To return to the previous screen, press the Exit button.
t
Setup Wizard
When you turn your BDS receiver on for the first time, the on-screen menu will display the
Setup Wizard.
Setup Wizard Page: 1/5
Next
Welcome to the Harman Kardon BDS Setup
Wizard.
Some simple information is needed to ensure
you get the best experience from your product.
You can adjust these settings later in addition
top making changes to more advanced settings
by pressing the ‘Settings’ button on the
remote.
OK
Before you can use your BDS system, you need to set the language and make a few basic
settings so that the BDS receiver’s video output will work properly with your TV. Press the OK
button and the Wizard’s language screen will appear.
Setup Wizard
Page: 2/5
Next
Please select which language you
would like the BDS menus to appear.
OK
Previous
English
Español
Français
Deutsch
Italiano
After setting the language you want the on-screen menus to use, press the OK button, and
the Wizard’s TV-resolution screen will appear.
Setup Wizard
Page: 3/5
Next
Please select the highest resolution that your
TV supports. If you are unsure, select ‘Auto’.
Upon making a selection the screen will be
changed to the chosen resolution. You will be
presented with the option to continue with the
new resolution or ‘Cancel’ to return to the
previous resolution. If the screen remains
blank, please wait 15 seconds without
pressing anything and the system will
automatically return to the previous resolution.
OK
Previous
Auto
480p/576p
720p
1080i
1080p
After selecting your TV’s highest resolution, press the OK button and the Wizard’s aspect-ratio
screen will appear. NOTE: If you’re unsure of your TV’s highest resolution, select “Auto,” and
BDS will automatically select the optimal resolution for you.
Setup Wizard
Page: 4/5
Next
Please select the best aspect ratio
that fits your TV.
OK
Previous
16:9 Full
16:9 Normal
4:3 Pan & Scan
4:3 Letterbox
After selecting the aspect ratio that best fits your TV, press the OK button to save your setting,
and then press it again to exit the Setup Wizard.
remote is programmed to operate your TV in the Aux control mode, you can also have the TV’s
channel +/– functions “punch through” and operate even when the remote is in the Disc,
Radio or iPod control modes.
Press and hold the button for the main device the remote will be operating. The button 1.
will light up, go dark and then light up again. Release the button.
Select the type of punch-through programming.2.
For “punch-through” channel control, press the Channel Up button.a)
For “punch-through” transport control, press the Play button.b)
Press the Aux button. The original source button will flash to confirm.3.
You can repeat Step 1 – Step 3 for any of the remote’s source-selector buttons (Aux, Radio
etc.). NOTE: “Punch-through” channel and transport commands will override the existing
commands for those buttons in the source modes you program.
To undo “punch-through” programming, follow the same steps as above, but press the same
source selector button in Step 1 and Step 3.
Using the Remote After it is Programmed
Pressing the remote’s Aux source-selector button will put the remote into the auxiliary-
control mode, and it will control the auxiliary component(s) via the codes you have
programmed into it.
To switch the remote back to the BDS receiver-control mode from the auxiliary-control mode,
press any one of these buttons: Disc, Radio, iPod or Home.