Harman-Kardon 347 Stereo Receiver User Manual


 
56 PROGRAMMING THE REMOTE
Programming the Remote
Notes on Using the AVR
Remote With Other Devices.
• Manufacturers may use different code sets for
the same product category. For that reason, it is
important that you check to see if the code set
you have entered operates as many controls as
possible. If it appears that only a few functions
operate, check to see if another code set will
work with more buttons.
• Depending on the brand and product type
used the functions listed in the Function List
tables may not correspond with the function the
unit reacts on the command. In these cases it’s a
good idea to edit the reaction of the unit into
the corresponding line of the table or to set up a
separate list.
• When a button is pressed on the AVR remote,
the red light under the Input Selector
45
for the product being operated should flash
briefly. If the Device Control Selector flashes for
some but not all buttons for a particular
product, it does NOT indicate a problem with the
remote, but rather that no function is
programmed for the button being pushed.
Volume Punch-Through
The AVR’s remote may be programmed to
operate the Volume Control
d
and the
Mute
c
from either the TV or the AVR in con-
junction with any of the devices controlled by the
remote. For example, since the AVR will likely be
used as the sound system for TV viewing, you
may wish to have the AVR’s volume activated
although the remote is set to run the TV. Either
the AVR or TV volume control may be associated
with any of the remote´s devices.
To program the remote for Volume Punch-
Through, follow these steps:
1. Press the Input Selector
4
for the unit you
wish to have associated with the volume control
and the Mute button
c
at the same time until
the red light illuminates under the Input Selector
4
and note that the Program Indicator
2
will flash amber.
2. Press the Volume Up button
d
and note
that the Program Indicator
2
will stop
flashing and stay amber.
3. Press either the AVR Selector
5
or the
Input Selector
4
, depending on which
system’s volume control you wish to have
attached for the punch-through mode. The
Program Indicator
2
will blink green three
times and then go out to confirm the data entry.
Example: To have the AVR’s volume control
activated even though the remote is set to con-
trol the TV, first press the Video/TV Input
Selector
4
and the Mute button
c
at the
same time. Next, press the Volume Up button
d
, followed by the AVR Input Selector
5
.
NOTE: Should you wish to return the remote to
the original configuration after entering a
Volume Punch-Through, you will need to repeat
the steps shown above. However, press the same
Input Selector in steps one and three.
Channel Control Punch-Through
The AVR’s remote may be programmed to oper-
ate so that the channel control function, per-
formed with the Sleep
9
and Surround
A
buttons, for either the TV, cable or satellite
receiver used in your system may be used in con-
junction with one of the other devices controlled
by the remote. For example, while using and
controlling the VCR, you may wish to change
channels on a cable box or satellite receiver
without having to change the device selected by
the AVR or the remote.To program the remote
for Channel Control Punch-Through, follow
these steps:
1. Press the Input Selector button
4
for the
device you wish to have the channel control
associated with and the Mute button
c
at the
same time until the red light illuminates under the
Input Selector
4
and the Program
Indicator
2
flashes amber.
2. Press the Volume Down button
d
.The
Program Indicator
2
will stop flashing and
stay amber.
3. Press and release the AVR
5
or Input
Selector button
4
for the device that will be
used to change the channels. The Program
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the VCR, first
press the VID 1/VCR Input Selector button
4
and the Mute button
c
at the same time.
Next, release them and press the Volume Down
button
d
, followed by the same Input
Selector button
4
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the same Input Selector
in Steps 1 and 3.
Transport Control Punch-Through
The AVR’s remote may be programmed to operate
so that the Transport Control Functions
P
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in con-
junction with one of the other devices controlled
by the remote. For example, while using and con-
trolling the TV, you may wish to start or stop your
VCR or DVD without having to change the device
selected by the AVR or the remote.To program
the remote for Transport Control Punch-Through,
follow these steps:
1. Press the Input Selector
4
for the device
you wish to have the channel control associated
with and the Mute button
c
at the same time
until the red light illuminates, under the Input
Selector
4
and the Program Indicator
2
flashes amber.
2. Press the Play button
P
.The Program
Indicator
2
will stop flashing and stay amber.
3. Press and release the AVR
5
or Input
Selector button
4
for the device that will be
used to change the channels. The Program
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button
4
and the
Mute button
c
at the same time. Next,
release them and press the Play button
P
,
followed by the CD Input Selector button
4
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the same Input Selector
in Steps 1 and 3.
NOTE: Before programming the remote for
Volume, Channel or Transport Punch-Through,
make certain that any programming needed for
the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.