Filter
Top Products
54 PROGRAMMING THE REMOTE
Example: One blink, followed by a one-second
pause, followed by six blinks, followed by a one-
second pause, followed by four blinks indicates
that the code has been set to 164.
For future reference enter the Setup Codes for
the equipment in your system here:
DVD ____________ CD ________________
VID1/VCR ________ VID3/TV __________
VID2/CBL/SAT ______________________
TAPE ______________________________
VID4 ______________________________
Learning Codes from a Remote
In addition to using codes from the remote’s
internal code library, the AVR 347’s remote is
able to “learn” codes from remotes that may not
be in the code library. In addition, you may use
this function to “learn over” the codes from a
preprogrammed device to add functions not
included in the preprogrammed codes.To learn
or transfer codes from an IR remote to the
AVR 347’s remote, follow these steps:
1. Place the front of the original remote with the
code being sent so that it is facing the IR
Transmitter Window
1
on the AVR 347
remote “head-to-head.”The remotes should be
between 2 and 4cm apart.
2. Select the button on the remote that you wish
to use as the device selector for the codes about
to be entered.This must be any of the Input
Selectors
4
or the AVR Selector
5
. Note
that when new codes are learned with the AVR
5
Selector, they may no longer control the
AVR 347.
3. Press the Input Selector
45
button
chosen and the Learn Button
h
at the same
time. Hold these buttons until the Program/SPL
Indicator
2
flashes amber and the light
under the device selector button turns red.
Release the buttons. It is important that you
begin the next step within 20 seconds.
4. Press the button on the AVR 347 remote that
you wish to program. Note that the Program/
SPL Indicator
2
will stop flashing.
Important Note: Codes cannot be taught to
all buttons on the remote. The buttons with the
following numbers are not learnable (for
numbers, see drawing on page 11):
4
,
7
,
8
,
B
,
I
,
O
,
Q
,
S
,
Y
,
c
,
e
,
h
. In these cases the Program/SPL
Indicator
2
keeps flashing after the button
was released.
5.As long as the Program/SPL Indicator
2
is on steadily (for five seconds), press and hold
the button on the original remote that you wish
to “teach” into the AVR 347 remote. If you
pressed the button too late or no command was
received within five seconds, the Program/SPL
Indicator
2
will flash red three times and
then amber, then simply repeat step four.When
the Program/SPL Indicator
2
turns green,
release the button on the original remote. Note
that the Program Indicator will then begin to
flash amber again.
NOTE: If the Program/SPL Indicator
2
turns red steadily during Step 5, the program-
ming was not successful. Repeat the steps to see
if the code will “take.” If the indicator keeps
flashing red in step 5, this code cannot be
taught.
6. Repeat steps 4 though 5 for each button on
the source remote that you wish to transfer to
the AVR 347 remote.
7. Once all codes have been transferred from the
original source remote to the AVR 347 remote,
press the Learn button
h
.This will turn off all
LEDs and turn off the learning mode.
8. Repeat Steps 1 through 7 for any additional
remotes you wish to “teach” into the AVR 347
Remote.
Erasing Learned Codes
The AVR 347’s remote allows you to remove or
erase the code learned into a single button for a
single device, to remove or erase all the codes
that have been learned for a single device, or to
erase all commands that have been learned to all
devices.
To erase a single learned code from
within a single device’s settings, follow
these steps:
1. Press and hold both the Input Selector
45
within which the individual button to be
erased has been programmed and the Learn
button
h
.
2.When the red LED under the Input Selector
turns red and the Program/SPL Indicator
2
flashes amber, release the buttons.
3. Press and release the Input Selector
45
again for the device within which the individual
button to be erased has been programmed.
4. Press the 7 button
H
three times.
5. Press and release the individual button for
which the code is to be erased.The
Program/SPL Indicator
2
will blink green
two times and then return to amber.
6.To erase other buttons within the same device,
press them as noted in Step 5.
7.When all buttons to be erased have been
pressed, press the Learn button
h
to complete
the process.
To erase all codes within a single device,
follow these steps:
1. Press and hold both the Input Selector
45
for which you wish to erase the codes
and the Learn button
h
.
2.When the red LED under the Input Selector
turns red and the Program/SPL Indicator
2
flashes amber, release the buttons.
3. Press and release the same Input Selector
45
again for the device whose codes you
wish to erase.
4. Press the 8 button
H
three times.
5.The Program/SPL Indicator
2
will turn off,
the red light under the Input Selector will flash
on and off once and the Program/SPL
Indicator
2
will flash green three times to
indicate that the codes have been erased.
To erase all codes that have been pro-
grammed to all devices in the remote,
follow these steps:
1. Press any Input Selector
45
and also
the Learn button
h
.
2.When the red LED under the Input Selector
turns red and the Program/SPL Indicator
2
flashes amber, release the buttons.
3. Press and release the same Input Selector
45
again.
4. Press the 9 button
H
three times.
5.The Program/SPL Indicator
2
will turn off,
the red light under the Input Selector will flash
on and off once and the Program/SPL
Indicator
2
will flash green three times after
some seconds to indicate that the codes have
been erased.
Programming the Remote