Filter
Top Products
120
6
Pressing ui, select the rst letter of the device
brand name. Then press ENTER.
A
B
C
Device : DVD
D
E
F
G
H
I
REMOTE SETUP GUIDE
1
Please select the first letter of
the brand name of the device.
Enter
RETURN
Return
Select
•The first character is displayed as 1, A to Z.
(Initials for the brand are displayed for each
category.)
For brand names that start with numbers
and symbols, select “1”.
7
Pressing ui, select the device
brand name. Then press ENTER.
Denon
Dantax
Disney
DSE
Durabrand
REMOTE SETUP GUIDE
Please select brand name.
-DVD-
Enter
RETURN
Return
Select
•When there are several pages of brand
names, the pages can be switched by
pressing the remote control unit’s CH + or
CH –.
NOTE
If the desired brand name is not listed, the supplied remote control
unit cannot control the device. Use the remote control unit supplied
with the device to be used.
Registering preset codes
8
The procedures for registering remote control codes
and remote control preset registration are displayed.
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
REMOTE SETUP GUIDE
Device
Brand
Code [1/3]
: DVD
: DENON
: 30490
Press QUICK 1 if device works, QUICK 2 if not
QUICK3
Return
QUICK2
NG
QUICK1
OK
NOTE
If a wrong brand name is selected, press QUICK SELECT 3. The
following screen is displayed:
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
REMOTE SETUP GUIDE
Device
Brand
Code [1/3]
: DVD
: DENON
: 30490
Press QUICK 1 if device works, QUICK 2 if not
QUICK3
Return
QUICK2
NG
QUICK1
OK
OK
Press [AMP] button.
And press [ENTER] button to return
Brand select menu.
Press AMP then ENTER to return to step 7.
9
Press the input source button on which the preset
code is to be registered (BD, SAT/CBL, TV, DVD,
V.AUX, DOCK, GAME1, GAME2 or CD).
•For TV, only the preset code for the categories “TV”, “TV/DVD”, or
“TV/VCR” can be registered.
10
Press and hold ZONE/DEVICE Z for at least 3 seconds.
The zone mode indicator flashes twice.
11
Enter a ve-digit code using 0 – 9.
Press the buttons with an interval less than 10 seconds.
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
REMOTE SETUP GUIDE
Device
Brand
Code [1/3]
: DVD
: DENON
: 30490
Press QUICK 1 if device works, QUICK 2 if not
QUICK3
Return
QUICK2
NG
QUICK1
OK
•When the code is registered.
The zone mode indicator flashes twice.
•When the code is not registered correctly
The mode indicator slowly flashes once. Perform from step 9
again.
•When an input number is not correct
Press ON once then perform the operations from step 9 again.
12
Operate the device being used to check the operation.
•If the device is operating, press QUICK SELECT 1.
Go to step 13.
•If the device is not operating, press QUICK SELECT 2.
Go to step 14.
13
The screen shown below is displayed, and registration
of the preset code is completed.
1. Press [INPUT SOURCE].
2. Press and hold [DEVICE ON ( l )] for 3 seconds.
3. Input code with [0-9].
4. Press any key to check device. (e.g. [DEVICE ON ( l )])
REMOTE SETUP GUIDE
Device
Brand
Code [1/3]
: DVD
: DENON
: 30490
Press QUICK 1 if device works, QUICK 2 if not
QUICK3
Return
QUICK2
NG
QUICK1
OK
OK
Remote Setup Guide is finished.
Press [AMP] button.
And press [ENTER] button to return
MENU.
•The menu screen is retrieved. Press AMP then ENTER.
Basic version
Advanced version
Information
Advanced version
vSee overleaf